It is recommended to apply Boracare to all sides of the wood for best results.
Wood should be sanded and treated with Bora-Care prior to staining, painting, sealing etc. Please wear protective gear included in our Professional Safety Kit when applying the product. You should wait a few days after application has dried.This will allow the product to soak through the entire piece of wood. Do not wait longer than six weeks to re-sand/stain/seal.
Yes, you can use Boracare to treat a wooden fence as long as the wood is raw, meaning it has not been painted, stained, or treated with any type of water sealant. Be sure you are diluting Boracare at a 1:1 ratio with water for active insect infestations. You would need to use a water sealant after the Boracare application is completely dry if you are treating wood that is exposed to rainfall. If the wood is not raw wood, then you can spot treat termite activity with a ready-to-use termiticide such as FUSE Foam.
Boracare is the best product we have to treat raw wood for powerpost beetles or other similar wood-boring insects. Boracare is there for the life of the wood, however, in very old wood there may not be enough moisture for the Boracare to get all the way to the center of larger beams. Unfortunately, you must have a special chamber to fumigate individual items - an antique dealer can often give a referral - otherwise you would need to have a professional company come out to tent and treat the entire structure. You can do a full pre-construction treatment with Boracare or Timbor on the new raw structural wood to help prevent infestations of wood-boring beetles, carpenter ants, termites, and wood decay fungus.
Unfortunately the Boracare? is not labeled for or to repel carpenter bees. For carpenter bees, we would recommend using our? Carpenter Bee Kit. It has everything inside of it to do a complete treatment for bees. Please also check out our? Carpenter Bee Guide? for wonderful tips on how to treat and prevent them in the future.
<body id="cke_pastebin" >
</body>
You will want to pressure wash, dry, apply Bora-Care (allow to dry) and then seal after.
We would recommend that you contact the Boracare manufacturer, Nisus, for further assistance. Nisus may be reached at 800-264-0870.
Bora-care is made for treating raw wood, if the wood has been painted, stained or treated in any way it will not absorb into the wood and therefore will not protect your wood.
Yes it is completely safe to use Boracare in the home on exposed studs as long as only the applicator is in the area while the product is being applied, and until the surface of the studs has dried. This could be as little as a couple of hours or as much as a day depending on how heavily you applied the product.
You should use a wood treatment product to treat powder post beetles. Bora-Care is the best wood treatment product available. Bora-Care will penetrate through the wood and kill the larvae eating the wood no matter where they are in the wood. However, it can only be applied to raw wood. It cannot be applied to wood that is painted, stained, or sealed. If your wood is painted, stained, or sealed, then you will need to drill holes and inject Bora-Care or sand the finish off of the wood, treat with Bora-Care, and then refinish the wood. Please check out our Powder Post Beetle Treatmen page. Here you will find a treatment guide along with the proper products to use.
When using Bora-Care on painted wood, you should drill a hole every 6 inches up/down the stud/posts to ensure good coverage.
Wood just needs to be dry before applying Bora-Care. It can take up to 48 hours for it to dry after application. It should dry clear when mixed as directed and would not affect stain once dry.
If Boracare was used correctly by the pest control company, it would only be on the raw wood surfaces within your attic. If any did somehow get on a floor or wall a rag with hot soapy water or a scrub brush dipped in hot soapy water should remove it.
You can certainly treat any raw lumber with Boracare before it is stored. If it is stored indoors, then you could apply stain, seal, etc. any time after the Boracare application is dry. If the wood is outdoors or otherwise exposed to rainfall, however, then you would need to apply a water sealant within 3 weeks of the Boracare application so that rainfall does not deplete the Boracare residual.
Yes, Bora-Care can be used on fly wood as long as it's raw wood, meaning no stain or any type of finish. If it's being applied to a bed set, you would need to wait until it has completely dried to be able to use the bed/bed set again, this can typically take approximately 48 hours, this would include if a fly wood wall after being treated.
There are 36 cases (144 bottles) of the Bora-care per shipping pallet. Yes, we do offer special discounts for larger orders. Please feel free to contact us at 866-581-7378 Ext. 378 for a free quote on your order today!
Anytime you’re applying chemicals, including Bora-Care, appropriate personal protection equipment is always recommended. You can view our Basic Safety Kit to view the products recommended when applying chemicals.
Since Bora-Care is designed to soak through to the center of the wood to protect the wood for it’s lifetime from wood boring pests, it is important to apply the product to all surfaces on the wood. We would recommend treating the logs prior to scribing to ensure you’re able to treat the entire surface of each log.
For tracking purposes (to make it easier to see where Bora-Care solution has been applied) an appropriate marker dye or pigment may be added. We suggest using Turf Mark Blue as this is an approved pigment dye used for Bora-Care.
Bora-Care is meant to be applied on all surfaces of raw, unfinished wood so it penetrates all the way to the center of the wood, and will last the lifetime of the wood.
