The first thing you need to know when using an herbicide such as Pin Dee 3.0 T&Ois that the exact amount of water you dilute it with is not important. It is only important to make sure you are using the correct amount of product per 1,000 sq ft of lawn. Use too much and you risk damaging your lawn, use too little and you will not get adequate results. You will need to use 1.3 to 1.8 fl oz per 1,000 sq ft depending on your turfgrass. To decide how much water you want to use, you should mark a 1,000 sq ft area, fill your sprayer with water ONLY, and start walking and spraying just as if you were doing the actual application of herbicide. When you are done walking and spraying the 1,000 sq ft area note how much water it took you to spray that area, and that is the amount you will want to mix 1.3 to 1.8 oz of product with for each 1,000 sq ft area that needs to be treated. You will need to make sure treated areas are irrigated with at least 1/2 inch of water (either by rainfall or by sprinkler) following the application
Per the label, an area can be reseeded or sod can be laid down three months after using Pin Dee 3.3 T&O Herbicide.
Pin Dee 3.3 T&O Herbicide is a pre-emergent herbicide that was labeled for use on any type of turf including dormant bermuda.
Yes, per the label for Pin Dee 3.3 T&O Herbicide to control broadleaf weeds, this product can be mixed with 2,4-D and other similar products. Please refer to the product label for complete instructions and precautions.
Typically a pre-emergent like Pin Dee 3.3 T&O Herbicide is applied at least twice a year depending on your region and the program you are following. Spring and fall are the usual times to apply. We do have general lawn care schedules here that may be helpful. Please contact your local cooperative extension office to determine the most exact timing of application as this will vary greatly from region to region.
For Pin Dee 3.3 Herbicide you will need to use 1.3 to 1.8 fl oz per 1,000 sq ft depending on your turfgrass. To decide how much water you want to use, you should mark a 1,000 sq ft area, fill your sprayer with water ONLY, and start walking and spraying just as if you were doing the actual application of herbicide. When you are done walking and spraying the 1,000 sq ft area note how much water it took you to spray that area, and that is the amount you will want to mix 1.3 to 1.8 oz of product with for each 1,000 sq ft area that needs to be treated. You will need to make sure treated areas are irrigated with at least 1/2 inch of water (either by rainfall or by sprinkler) following the application.
Pin Dee 3.3 T&O Herbicide can be tank mixed with other products such as RoundUp following all instructions on each product label. Do not apply tank mixtures containing glyphosate over the top of ornamental plants. Before tank mixing, a simple jar test is recommended to insure compatibility of herbicides. Always read the companion product label. Follow all use precautions and restrictions that apply to each product used. Always follow the most restrictive label.
A professional grade pre-emergent such as Pin Dee 3.3 EC can have soil residues of up to 6-8 months, depending on the rate used (based on treatment area and program following, and factors such as how sandy the soil is how much rainfall you receive.
Pin Dee 3.3 T&O Herbicide is safe around pets when used as directed. Per the product label, keep pets out of the area until it has dried, typically 4-6 hours is safe to return them.
The first thing you need to know when using an herbicide such as Pin Dee 3.0 T&Ois that the exact amount of water you dilute it with is not important. It is only important to make sure you are using the correct amount of product per 1,000 sq ft of lawn. Use too much and you risk damaging your lawn, use too little and you will not get adequate results. You will need to use 1.3 to 1.8 fl oz per 1,000 sq ft depending on your turfgrass. To decide how much water you want to use, you should mark a 1,000 sq ft area, fill your sprayer with water ONLY, and start walking and spraying just as if you were doing the actual application of herbicide. When you are done walking and spraying the 1,000 sq ft area note how much water it took you to spray that area, and that is the amount you will want to mix 1.3 to 1.8 oz of product with for each 1,000 sq ft area that needs to be treated. You will need to make sure treated areas are irrigated with at least 1/2 inch of water (either by rainfall or by sprinkler) following the application.
