The setting to use on a spreader will depend on the product being used. The setting instructions are found on the back side of the fertilizer bag, the spreaders they list will be ones the manufacturer has tested their product on. If you don't find the Scotts Turf Builder Classic Drop Spreader listed on the bag it doesn't mean it can't be used, it just means you will have to calibrate it to find out what setting is the right one. You can see the video on the spreader's page or you can follow these instructions:
Calibrating the spreader:
Check the calibration by first adjusting your micrometer setting to 6. Turn the spreader over so that you are looking at the outside of the bottom of the hopper. Use your foot to hold down the trigger. With the micrometer set at 6 and the trigger squeezed against the handle, the front edge of the projecting ridge on the shut-off bar should be aligned with the calibration line located on the 2nd or 3rd tooth from the center. To adjust the alignment,, use a small wrench to turn the black calibration screw at the lower end of the control wire leading from the micrometer rate setting barrel. Adjust the screw until the calibration line and raised ridge or front edge of the shut-off bar meet.
For Rectangular Lawns: Apply two header strips across each end for a turning area. Then apply back and forth in the longest direction.
For Irregular-Shaped Lawns: Apply one header strip around the entire lawn for a turning area, then apply back and forth.
Spreader Overlap: To avoid streaks or misses, overlap spreader patterns approximately 1-1/2 feet (50 cm). Do not leave spreader open when making turns.
According to Scotts, the manufacturer, the setting for the Scotts Turf Builder Classic Drop Spreader will depend on the exact product you are using. Scott representatives can be reached at 888-270-3714 and they are able to provide the exact spreader setting for the product you are using.
Scotts Turf Builder Classic Drop Spreader is designed to apply granular products, not soil. You may check with Scotts directly to see if they have a spreader you can use 888-270-3714.
We do have Prime Source Indicator Blue SG. This is water soluble granule that could potentially be mixed with a granule and applied to the soil. You may need to wet the lawn first in order to see where the product has landed.
Do be mindful that with most insecticide granules, they are falling beyond the thatch layer and so will the Prime Source Indicator Blue SG. This will in turn turn the soil blue and you may not be able to see exactly where the product was applied.
Milky Spore can be applied with any drop spreader that can be calibrated to the rate needed for application including the Scotts Turf Builder Classic Drop Spreader.
Unfortunately, we do not have the spreader settings for Scotts Turf Builder Classic Drop Spreader and the manufacturer does not list that spreader on their bag. Due to the thousands of granules on the market and just as many different types of spreaders, you will want to calibrate your spreader to the product you are using and its application rates. Please take a moment to watch our How to Calibrate your Spreader Video for step by step instructions on how to do this.
We do not see an issue using Scotts Turf Builder for top mix. For the correct calibration, please contact Scotts at 888-270-3714.
We would recommend to contact Scotts as the setting varies depending on the product. 1-888-295-6902
We apologize but we are unsure of what setting you would be looking to use for the Scotts Turf Builder Classic Drop Spreader. It would be best to contact the manufacturer since they are going to be the best experts on their own products and could advise you in a more accurate fashion. You can reach Scotts directly at 1-888-270-3714.
No, the Scotts Turf Builder Classic Drop Spreader is meant to operate with both wheels turning as you walk to apply the granule. Please contact Scotts directly at 1-888-270-3714 to troubleshoot for your spreader.
Unfortunately, we do not have this information available as this can vary from spreader to spreader and can depend on the product being used. For the equivalent setting for the Scotts Turf Builder Classic Drop Spreader using your preferred product, we would recommend reaching out to the manufacturer directly at 888-270-3714. The other option would be to calibrate your spreader yourself. We have a very helpful video on How to Calibrate your Spreader here.
Unfortunately, we do not have the spreader settings for Scotts Turf Builder Classic Drop Spreader and DuraTurf and the manufacturer does not list that spreader on their bag.
Due to the thousands of granules on the market and just as many different types of spreaders, you will want to calibrate your spreader to the product you are using and its application rates.
You can see a short video on How to Calibrate your Spreader HERE. If further assistance is needed, we suggest contacting Bonide directly for assistance on spreader settings for their product.
