-
Asked by Django from Cincinnati07/02/2013QI used AmTide Imidacloprid 2F T and O to treat for emerald ash borer, it rained 3 hr after i put it on
i soaked the roots with 25 gallons of solution for a six foot in diameter tree. about three hours later it rained for 12 hours straight. will i need to start over?ANo rain will not effect AmTide Imidacloprid 2F. If anything it would have helped to soak in better.
-
Asked by Clint from Cincinnati, Ohio09/28/2015QHow much water do I use when mixing AmTide Imidacloprid 2F T and O to treat emerald ash borer?A
Per the instructions on the product label for AmTide Imidacloprid 2F T and O when treating for Emeral Ash Borers: 0.1 to 0.4 fl. oz. (3 to 12 mL) per inch of trunk diameter (D.B.H.) You may use the higher rate (0.3-0.4 fl. oz.) only for trees >15 inches (DBH) to control Asian longhorned bee…
Read Full Answer »Per the instructions on the product label for AmTide Imidacloprid 2F T and O when treating for Emeral Ash Borers: 0.1 to 0.4 fl. oz. (3 to 12 mL) per inch of trunk diameter (D.B.H.) You may use the higher rate (0.3-0.4 fl. oz.) only for trees >15 inches (DBH) to control Asian longhorned beetle, Emerald ash borer, Eucalyptus longhorned borer, Bronze birch borer and Alder borer. Diameter at Breast Height (DBH) is measured at 4.5 feet from the ground. Soil Drench: Uniformly apply the dosage in no less than 10 gallons of water per 1000 square feet as a drench around the base of the tree, directed to the root zone. Remove plastic or any other barrier that will stop solution from reaching the root zone. -
Asked by T from Newnan, Ga 3026302/17/2015QCan AmTide Imidacloprid 2F T and O be applied by method of tree injection?A
No, the AmTide Imidacloprid 2F T and O product label only gives application instructions to trees via soil injections or soil drenches.
-
Asked by Carol from Jefferson City08/05/2015QWill 1 gallon of AmTide Imidacloprid 2F cover 3.5 acres when targeting Japanese Beetles?
I have a pull-behind 45 gallon sprayer.AWhen using AmTide Imidacloprid 2F to target Japanese Beetles you need to use a rate between 19.2 to 25.6 fluid ounces per acre. For 3.5 acres using between 67.2 to 89.6 fluid ounces will be sufficient. Please see the product label for complete application instructions. If you need anymore infor…
Read Full Answer »When using AmTide Imidacloprid 2F to target Japanese Beetles you need to use a rate between 19.2 to 25.6 fluid ounces per acre. For 3.5 acres using between 67.2 to 89.6 fluid ounces will be sufficient. Please see the product label for complete application instructions. If you need anymore information on Japanese Beetles, please visit our Japanese Beetle Control page. -
Asked by Laura from [email protected]04/16/2015QWhat size is AmTide Imidacloprid 2F T and O?A
AmTide Imidacloprid 2F T and O is sold in 1 gallon containers.
-
Asked by Robert from Twin Bridges, Mt06/25/2016QWhen using AmTide Imidacloprid 2F, is it mixed with water or sprayed using the spray only?A
AmTide Imidacloprid 2F T and OÂ is a concentrated insecticide that should be mixed with water. Please read the Product Label for complete mixing and use instructions.
-
Asked by Alan06/17/2019QWhat ratio for AmTide Imidacloprid 2F T and O should I set my dosatron injector pump in my greenhouse for soil drench application?
Pots are 2 gallon and have chestnut trees in them.AThe normal dilution ratio is 1:100 to 1:200, depending on the system per the product label for the AmTide Imidacloprid 2F T and O. Please refer to the product label for complete instrutions and information in using in irrigation systems.