Bor8 Rods 1/2" x 4"

Bor8 Rods 1/2\

Have a Question? Ask Our Pros!

Call Us: 866-581-7378
Mon-Fri 9am-5pm ET
Email Our Pros
We're here to help
Live Chat
Offline. Leave Us a Message

You May Also Need

Average Rating

There are no reviews for this product yet. Be the first.

Product Overview

The Bor8 Rods 1/2" x 4" is highly recommended for pre-treatment and remedial protection of wood against decay and insects. It is for use in lumber, timber or log with permanent or periodical moisture content above the fibre saturation point. It is placed in such a way that moisture will disseminate the aimed loading of preservative all over the target area. The Bor8 Rods in 1/2" x 4" is intended for a 6" x 6", 6" x 8" and round wood up to a 6 inch diameter wood size. To install, insert the rods into decaying wood or wood in high-risk areas through drilled holes. See Bor8 Rod Size and Spacing Chart to determine specific applications. Picture is used as a reference only, please disregard size indicated.

Other order options also comes in 100 in a box or 750 in a pail.

Other Bor8 Rod sizes available: 1/4" x 1/2", 1/3" x 1", 1/3" x 2 5/8", 1/2" x 2", 3/4" x 3"

Features and Specs

Active Ingredient Anhydrous Disodium Octaborate - 96.65%
Target pests Fungal Decay
For use in Residential and Commercial: Preventing and eliminating fungal organisms on wood products like lumber, timbers, logs, millwork, poles, piles, posts, crossties, laminated beams and others.
Application Bor8 Rods can be inserted into any wood surface in a staggered, linear, or angled pattern through drilled holes.
NOT FOR SALE TO
Dimensions 1/2" x 4"
Special Features Stops existing rot and also prevents rot in wood.
Shipping Weight 1.00 lbs
Manufacturer Wood Care Systems (Mfg. Number: Bor8 Rod 1/2 x 4-12)
EPA Registration 10465

Details

DIRECTIONS FOR USE:

Bor8 Rods can be inserted into any wood surface in a staggered, linear or angled pattern.

  • Determine the number of Bor8 Rods required. Starting 2 inches from a joint or the end of the wood, the entire length of the wood should be covered in order to ensure moisture will evenly distribute the preservative throughout the target area. Do not exceed 12 inches on center for linear spacing along the grain and do not exceed 4 inches for spacing across the grain.
  • Drill appropriate sized holes to accommodate the predetermined number and size of Bor8 Rods required. For a snug fit and to ensure even distribution, drill the holes 1/16 inch greater in diameter than the preservative rods. In addition, to allow for expansion, leave a minimum of 1/8 inch of air space between Bor8 Rods and plug.
  • Insert the suitable size and number of Bor8 Rods into the holes.
  • Seal the hole with a treated wood dowel, wood filler or caulk.
  • After installation, paint or any other type of surface coating may be applied to the wood if desired. Install Bor8 Rods in the general vicinity of where the potential for decay is greatest or where decay exists.

Bor8 is available in 6 different sizes: 

  • Bor8 Rods - 1/4" X 1/2"
  • Bor8 Rods - 1/3" X 1"
  • Bor8 Rods - 1/3" X 2 5/8"
  • Bor8 Rods - 1/2" X 2"
  • Bor8 Rods - 1/2" X 4"
  • Bor8 Rods - 3/4" X 3"

See Bor8 Rod Size and Spacing Chart for specific applications for all wood sizes.

There are no reviews for this product yet. Be the first.

Questions & Answers

Have a question about this product?

There are no questions for this product yet. Ask the first.

From $68.82 + Free Shipping*