Buy 2 or more: $26.53 each
Have a Question? Ask Our Pros!
Hi-Yield Stump Remover is a product that decomposes the stump from the inside out. Hi-Yield Stump Remover makes the stump porous through out so that removing or burning is easier to do. Use the directions on the label for diagrams of where to drill holes in the stump for proper application. Hi-Yield Stump Remover will not harm surrounding vegetation.
Product Documents
| Active Ingredient | Sodium Metabisulfite 100% |
|---|---|
| Target pests | Nuisance and unsightly stumps |
| Application | * See label for complete application instructions (proper drilling and illustrations on stump removal) |
| Pet safe | Yes, if used as directed on Label |
| Shipping Weight | 1.66 lbs |
| Manufacturer | VPG (Mfg. Number: 32015) |
| UPC | 732221320154 |
DIRECTIONS FOR USE
Use this to remove nuisance and unsightly stumps. HI-YIELD STUMP REMOVER decomposes the wood of tree stumps leaving them porous. The decomposition, depending on the size of the stump, may take several weeks or months. This allows for easy removal or burning of the stump. HI-YIELD STUMP REMOVER is harmless to vegetation surrounding treated stumps. For removal of stumps up to 12” in diameter, drill a 1” hole in center of stump approximately 10” to 12” deep. Drill an additional 1” hole into the side of the stump approximately 3” below the top of the stump. This second hole should be slanted to connect (or nearly so) with the bottom of the center hole. Drill several sets of such holes for stumps larger than 12” wide.
Pour approximately 4 oz. of HI-YIELD STUMP REMOVER into each hole. It works best when weather is warm and stumps are dry. Fill each hole with water. Allow to stand from four to six weeks.If stump is to be burned, refill holes with kerosene or fuel oil. Allow sufficient time for the liquid to be completely absorbed into the stump.
Then apply a slight amount of kerosene over stump and ignite. Or burn charcoal on top of stump or around base to start stump burning. The stump will burn with a smoldering, red glow, clear down to the roots, disintegrating the stump into ashes.
Time needed
By Hgc on 11/26/2016
Decomposition of a stump takes time. Several applications --of this or any priloduct, even straight nitrogen-- are needed. No change will be visible for at least a few months. After that, progress is much quicker. Expecting a stump to disappear in a few days or a week is naive at best.
Was this review helpful to you? YesNo
45 of 48 people found this review helpful
DOSE NOT WORK
By Ron on 05/11/2016
This is a long process .
By Ted on 07/29/2018
This will take years to work as described. It may not be much less expensive than having the stump removed by pros. I add more product when the level goes down. I started about 100 days ago. I do believe it is working. Ask again a year from now.
Was this review helpful to you? YesNo
14 of 15 people found this review helpful
Too soon to tell
By Gene on 06/26/2020
As advertised, this product takes a very long time to work, on the order of many months. It's only been 4 weeks since I drilled the holes and applied the stump remover, I was not expecting much progress. My stump was only about 10" in diameter cut pretty close to the ground so I've had enough product to refill the holes a couple of times since the initial application.
Was this review helpful to you? YesNo
6 of 6 people found this review helpful
Know what to ask for
By Sandra on 05/15/2020
juniper stumps approximately 10 inches in diameter
Was this answer helpful to you? YesNo
25 of 26 people found this answer helpful
I had very large silver maple taken down and it has stump that is about 2ft radius will this work on something that size?
Was this answer helpful to you? YesNo
7 of 9 people found this answer helpful
Once you've drilled holes into the stump as specified by the label, you will pour approximately 1/4 lb. of Hi-Yield Stump Remover into each hole. Fill each hole with water and allow it to stand from four to six weeks.
Was this answer helpful to you? YesNo
7 of 9 people found this answer helpful
Yes, Hi-Yield Stump Remover is a product that decomposes stumps from the inside out. It makes the stump porous throughout so that removing or burning is easier to do.
Was this answer helpful to you? YesNo
6 of 8 people found this answer helpful
The active ingredient in Hi-Yield Stump Remover is Potassium nitrate 95-99%.
Was this answer helpful to you? YesNo
1 of 1 people found this answer helpful
Hi-Yield Stump Remover
Rating: 2.8 (6 Reviews / 5 Q&A)
