PRODUCT USE RESTRICTIONS

FAILURE TO FOLLOW DIRECTIONS AND PRECAUTIONS ON THIS LABEL MAY RESULT IN CROP INJURY, POOR DISEASE CONTROL, AND/OR ILLEGAL RESIDUES.

APPLICATION INFORMATION

Inspire Super is a broad-spectrum product containing two fungicides. It has preventative, systemic and curative properties and is labeled for the control of many important plant diseases. Inspire Super provides excellent disease control of many leaf spots and powdery mildews. Inspire Super is applied as a foliar spray and can be used in block, alternating spray, or tank-mix programs with other crop protection products. All applications should be made according to the use directions that follow.

For the crops to which aerial applications are allowed, refer to the specific crop directions for use

PRODUCT USE INSTRUCTIONS

Application: Thorough coverage is necessary to provide good disease control. Make no more spray solution than is needed for application. Avoid spray overlap, as crop injury may occur.

Adjuvants: When an adjuvant is to be used with this product, the use of an adjuvant that meets the standards of the Chemical Producers and Distributors Association (CPDA) adjuvant certification program is recommended.

Efficacy: Under certain conditions conducive to extended infection periods, use another registered fungicide for additional applications if the maximum amount of Inspire Super has been used. If resistant isolates to Group 3 or Group 9 fungicides are present, efficacy can be reduced for certain diseases. The higher rates in the rate range and/or shorter spray intervals may be required under conditions of heavy infection pressure, with highly susceptible varieties, or when environmental conditions are conducive to disease.

Integrated Pest Management (IPM): Integrate Inspire Super into an overall disease and pest management strategy whenever the use of a fungicide is required. Follow cultural practices known to reduce disease. Consult your local agricultural authorities for additional IPM strategies established for your area. Inspire Super may be used in State Agricultural Extension advisory (disease forecasting) programs which recommend application timing based on environmental factors favorable for disease development.

MIXING INSTRUCTIONS

• Inspire Super is an oil-in-water emulsion (EW) formulation.
• Prepare no more spray mixture than is required for the immediate operation.
• Thoroughly clean spray equipment before using this product.
• Agitate the spray solution before and during application.
• Rinse spray tank thoroughly with clean water after each day’s use and dispose of pesticide rinsate by application to an already treated area.

SPECIFIC DIRECTIONS FOR USE

• Almonds
  • Alternaria Leaf Spot, Anthracnose, Blossom Blight, Green Fruit Rot, Leaf Blight, Leaf Rust, Scab, Shot Hole,
  • 16 - 20 fl oz/Acre
  • For blossom blight, apply 16-20 fl oz of Inspire Super during the bloom period.
  • For Alternaria leaf spot and scab, begin applications prior to disease onset when conditions are conducive for disease. If monitoring or history indicates the presence of Alternaria, apply 20 fl oz/A of Inspire Super in the late spring (mid-April to the beginning of May) and then repeat the treatment 2-3 weeks later.
  • For all other diseases, use 16-20 fl oz/A. Begin applications prior to disease onset when conditions are conducive for disease. Apply Inspire Super on a 14- to 21-day schedule.
  • Make no more than 2 sequential applications before alternating to another fungicide with a different mode of action.
  • The minimum retreatment interval is 14 days.
  • If disease pressure is high, use the shortest interval and highest rate.
• Bean, Dried
  • Anthracnose, Alternaria leaf spot, Alternaria blight, Ascochyta leaf and pod spot, Ascochyta blight, Cercospora leaf spot, Gray mold
  • 16 - 20 fl oz/Acre
  • Begin applications prior to disease onset when conditions are conducive for disease. Apply Inspire Super on a 14-day schedule making no more than 2 sequential applications before alternating to another fungicide with a different mode of action.
  • If disease pressure is high, use the highest rate.
• Pecans
  • Downy Spot, Pecan Scab, Powdery Mildew
  • 16 - 20 fl oz/Acre
  • Begin applications prior to disease onset when conditions are conducive for disease. Apply Inspire Super on a 14- to 21-day schedule, making no more than 2 sequential applications before alternating to another fungicide with a different mode of action.
  • If disease pressure is high, use the shortest interval and highest rate.

*See label for a complete list of crops and application rates.