Tool and Hardware Starter Kit

The Tool and Hardware Starter Kit includes:

• 1 x Carrying Case – Carries all the contents of the tool kit.
• 1 x Net Cable – Galvanized construction cable that is standard for perimeter support. Includes 1 roll of 250 ft. cable.
• 1 x Magnetic Nut Setter 1/4 in. - Can be used for driving self-tapping screws with a cordless hand drill, while the magnetic tip holds the screw in place while you start the hole.
• 1 x Net Scissors - Heavy Duty - A heavy-duty scissor that is simply a must in any netting job
• 1 x Cable Cutters Heavy Duty This sharp and long-lasting tool makes cutting heavy-duty cable much easier. It gives a clean cut up to 5/32 in. because if its overlapping heads, plus it features spring loaded rubber grip handle and security locking latch.
• 1 x Ratchet Crimping Tool - It offers the strongest and most discreet system in securing cable-end loop for a long lasting hold on tumbuckle or cable-end fastener.
• 1 x Net Ring Tool - Standard tool that helps attach netting to the cable, and it can accept a cartridge of 50 net rings for a quick and easier use.
• 1 x Net Rings Galvanized (2500) - The galvanized net rings helps hold the netting to the cable. Includes 1 box of Net Rings Galvanized.
• 1 x Digital Track Tester – This tester reads in 100-volt increments and it helps you check if your system is sending the correct amount of electricity.
• 1 x Flex Track Lead Out Wire, Black (50ft) - A twisted copper, 14 gauge double wire. This easy to cut, strip and crimp wire comes in 50 ft. per roll.
• 1 x Connector Crimp Tool - It helps deliver the perfect crimp to create a solid connection.
• 1 x New Bird Barrier Bond 10.1 oz - An adhesive that securely holds metals and plastics to wood, sheet metal, steel, brick, concrete and most building subtrates.
• 1 x Dripless Ergonomic Caulk Gun - A simple and automatic caulk gun that is used for bird barrier bond or bird-off gel.
• 1 x Birdwire Stainless (250ft) - Seven-stranded, stainless steel wire that is coated with U.V.-stabilized clear nylon. Kit includes 1 roll or 250 ft. wire.
• 1 x Snipping Tool - Helps with your snipping needs.
• 1 x Bird Barrier Product Installation - Assists you with the installation of your Bird barrier products.
• 1 x Lag Screw Driver - It does not require a plastic anchor sleeve, the bent shaft holds it securely in place.
• 1 x SDS 12mm Drill Bit Masonry - For use with the M6 galvanized netbolts.
• 1 x SDS 4.8mm Drill Bit Masonry - For use with the Metal-Hit Anchor and Net Spike.
• 1 x SDS 6.5mm Drill Bit Masonry - For use with both the 1 in. and 1.5 in. Split Pins as well as Anchor Rivets.
• 10 x 2.5mm Aluminum Ferrules - May be used with galvanized cable that works best on dry and salt-free climates. Use 2 ferrules per cable loop attachment.
• 2 x Turnbuckle Galvanized, Small - Used for cable runs under 25 feet.
• 10 x Multi-Use Cable Bracket - Can be used as a corner or intermediate attachment. It can also be installed as a permanent fixture of as a quick-release cable holder.
• 10 x Self-Tapping Screw Small Galvanized - Used to fasten Bird Barrier brackers and clips to different metals.
• 10 x Black Plastic Wire Guides Small - This lead wire guides helps in keeping the lead-out wire in place. Product comes in 100 pieces per pack.
• 5 x Bird Shock Warning Labels - A bold plastic warning labels must be placed evidently on the buildings. This warning label may be glued or screwed to the ledge or the side of the building. Product comes in 10 pieces per pack.
• 5 x Bird Wire Posts 3.5 in . - 3.5-inch post for use with glue-on bases.
• 5 x Bird Wire Posts 5 in. - 5-inch post for use with glue-on bases.
• 2 x Birdwire Glue-On Bases - Can be glued on properly prepared metal or wood when drilling is not an option.
• 10 x Birdwire Crimps - Lets you thread Birdwire through nickel–plated copper crimp to help connect it to bird posts or split pins.
• 10 x Micro Spring - A less conspicuous micro-spring that is made from 316 grade stainless steel which features one slightly opened loop to help facilitate attachment to bird post or split pin.
• 2 x M6 Netbolt Galvanized - A netbolt that can anchor most masonry stone or concrete corner/end attachments.
• 2 x Eye Bolt with Nut Galvanized - Corner/end attachment for an I-beam or other thick metal.
• 2 x Screw Eyes Heavy Duty Galvanized - Ideal for cable ends and corners when anchoring in wood.
• 10 x Split Pin Stainless 1 in. - This Split Pin is for use with the corresponding 1 in. Anchor Rivet. May be used for stone, masonry, or brick. Different lengths are available depending on the substrate integrity and use.
• 10 x Anchor Rivets 1 in. - Low-Profile nylon Anchor provides a secure installation when drilling into stone, masonry, or brick.
• 10 x Net Spike Galvanized - May be used for stone, concrete or solid brick.
• 10 x Lag Screw Large Galvanized - It does not require a plastic anchor sleeve, the bent shaft holds it securely in place.
• 2 x Turnbuckle Galvanized, Medium - Turnbuckle for cable runs between 25 feet and 75 feet.
• 2 x Flex-Track Straight Connectors - Connectors that are installed in seconds and designed to be attractive and long lasting. Product is made from durable, UV-stabilized plastic with locking tabs.
• 2 x Flex-Track Corner Connectors - Product is made from durable, UV-stabilized plastic with locking tabs.
• 2 x Turnbuckle Galvanized, Large - Turnbuckle for cable runs over 75 feet.
• 10 x Standard Springs - Standard sized springs are made from 316 grade stainless steel that features one slightly opened loop to help facilitate attachment to bird post or split pin.
• 5 x Corner Connector Kit - Includes 100 male and 100 female corner connector.
• 5 x T Junction Kit - Includes 100 male, 100 female and 50 piggyback connector.
• 5 x Straight Connector Kit - Includes 100 male and 100 female straight connector.
• 5 x Connector Female T Snap - Contains 50 taps per kit.
• 1 x Flex Track Adhesive Pads (10) – Pack of adhesive pads for use with Flex Track.