It is best to have two seperate sprayers, one for herbicides and one for insecticides. If this is not possible, you will need to triple rinse the entire sprayer, tubing, tank etc after each and every use. Never leave mixed solution in your sprayer, as this can cause damage to your equiptment.
The extra wand length on the B&G Sprayer 1 Gallon 18 in. Wand (N124-S-18) vs the 9 inch wand would just make applications easier by you not having to bend down as far to apply products. The 18 inch is generally the more popular sprayer for this reason.
If you drilled the holes 12 inches apart, then you would have 10 holes over 10 feet that you are trying to fill with 4 gallons. This works out to be a little less than half a gallon per hole. To fill these I would recommend using the one gallon sprayer on a "pin stream" setting so you can force the liquid down the hole and not splash it everywhere. You could use the B&G 1 Gallon Sprayer N124-S-18. You can also use a funnel and pour the termiticide down the holes. For more information on treating for termites, please click the link below.
The B&G Sprayer 1 Gallon 18 in Wand (N124-S-18) would be great for indoor and outdoor perimeter use for general pest control. To reach the height of 30 feet, you would want to use the Chapin Slide Pump Sprayer which will reach up to 30 ft.
There is some assembly required when you receive the B&G Sprayer 1 Gallon 18 in. Wand (N124-S-18). The hose and wand will need to be attached. The sprayer comes with a 4 way tip that features 2 sizes of pin-stream and 2 sizes of fan spray patterns
The B&G Sprayer 1 Gallon 18 in. Wand (N124-S-18) should be triple rinsed after use and the wand flushed with just water to ensure any residual product is removed and allowed to dry before storing. Be sure to keep out of freezing temperatures so that the brass wand is not damaged.
Unfortunately, the B&G Sprayer 1 Gallon 18 in. Wand (N124-S-18) does come with a pressure relief valve. It is located in the actual wand itself.
Yes, it is fine to use different products out of the same sprayer such as the B&G Sprayer 1 Gallon 18 in. Wand & Extenda-Ban Valve (N124-S-18), as long as you triple rinse the sprayer and wash it out thoroughly. Triple rinse means to rinse out the inside of the sprayer 3 times, and also fill it with water and run clean water through the hose for at least 1 minute to make sure that there is no residual left in the hose in addition to the tank. We also sell tank cleaners that are excellent for removing any possible residual from your sprayer.
The B&G handheld pump sprayers are offered with a 9", 18" and 24" wand. The B&G 24'' SS Extension (VE-164-SS) (22045710) can be used for extending the reach of B&G Sprayers.
To attach a B&G 24" stainless steel extension to an 18" Extenda-Ban, simply screw the threaded end of the extension directly onto the female threaded connection on the end of the Extenda-Ban valve body; ensure the O-ring on the extension is properly seated before tightening securely with a wrenchView the product manual HERE and for further technical assistance, B&G can be reached at 1-800-544-8811 or by emailing at [email protected]
The tip that comes with the B&G Sprayer 1 Gallon 18 in. Wand (N124-S-18) is the 4 Way Tip 5800 that features 2 sizes of pin-stream and 2 sizes of fan spray patterns. The B G 5800-CC Multeejet Crack and Crevice Tip has a small opening to allow you to insert a small straw to perform a crack and crevice treatment.