Stryker 54 is a contact insecticide aerosol spray that works as a great flushing agent as well. This knocks insects down immediately and dissipates quickly leaving no residue. Stryker 54 can be used for space treatment, on mattresses, indoors, outdoors and in food handling establishments.
Knocks insects down and dissipates quickly; leaves no pesticide residue.
Can be used in Green or sensitive accounts.
Natural/botanical insecticide + synergists for quick knockdown (contact kill) with no pesticide residue.
All outdoor applications must be limited to spot or crack and crevice application only, except for the following permitted uses:
Treatment to soil or vegetation around structures.
Applications to lawns, turf and other vegetation.
Applications to building foundations, up to a maximum height of 3 feet.
Other than applications to building foundations, all outdoor applications to impervious surfaces such as sidewalks, driveways, patios, porches and structural surfaces (such as windows, doors and eaves) are limited to spot and crack-and-crevice applications only.
Crack And Crevice Application:
Inject this into cracks & crevices or void spaces where insects may be harboring, living and breeding. Place injector tip into cracks, crevices, holes and other small openings. Apply product for 1 sec. For light infestations, move injector tip along cracks while treating at the rate of 3 ft/sec. For heavy infestations, move injector tip along at 1 ft/sec. For treatment of inaccessible voids (including wall and equipment voids), calculate the void’s cubic area and treat at the rate of 3 – 5 sec/3 ft3. Several holes may be required in long-running voids.
Apply the product in short bursts into the area where insects are to be contacted such as corners of the room, behind and under furniture or equipment. Apply from a distance of 18 - 24” from the surface and allow the material to drift to the area to be treated. The amount of product applied is not to exceed 10 sec/room for residential areas or 10 sec/100 ft2 for commercial areas.
Turn off air conditioners, fans, close doors and windows before treating. Calculate the cubic footage of the area to be treated and apply as follows: Flying Insects: Apply at the rate of 1 – 3 sec/1,000 ft3.
Apply at a rate of 20 sec/1,000 ft3. Disperse toward areas suspected of harboring the greatest insect infestations. Disperse in all locations contacting as many insects as possible.
Keep area closed for 15 minutes. Open and thoroughly ventilate before reoccupying.
Cluster Flies, Clover Mites, Flies, Fruit Flies, Gnats, House Flies, Mosquitoes, Small Flying Moths and Stable Flies, Wasps and Bees:
Perform directed spray and/or void treatments in infested areas.
INSIDE STRUCTURAL VOIDS:
Locate all insect entrances and close all but one opening. Apply through that opening.
Treat harborage areas such as behind baseboards, sinks, cabinets, meter boxes, door frames, corners of rooms and windows. Open and thoroughly ventilate the treated area before reoccupying.
Take bed apart. Treat joints and channels if hollow, such as square or round tubing, and see that the interior framework is treated. Treat mattresses, especially tufts, folds, and edges. Cover mattresses with clean bedding before use. When bed bugs are found in upholstered furniture, apply only to the infested tufts, seams, folds, and edges and underneath all areas, but DO NOT apply to flat surfaces where human contact will occur. Apply as a Crack & Crevice treatment to all baseboards, moldings, beneath floor coverings and carpets, closets, shelves, curtains, furniture, and picture frames. Direct spray into areas where bed bugs harbor. DO NOT use in patient rooms in hospitals and nursing homes for treatment of bed bugs. Reapply every 7 to 10 days, as needed, until infestation is eliminated.
Carpet Beetles (in Residences):
Hold product 36” above floor and direct spray toward floor and lower walls, treating at the rate of 10 sec/100 ft2. Also apply as a Crack & Crevice treatment to cracks and crevices near the source of the infestation.
Locate source of infestation. Apply to nearby cracks and crevices and perform a space treatment of the infested area at the rate of 5-10sec/1,000 ft3.
Stored Product Pests - exposed adult and larval stages of Angoumois Grain Moths (crawling), Carpet Beetles, Chocolate Moths, Cigarette Beetles, Confused Flour Beetles, Drugstore Beetles, Grain Mites, Granary Weevils, Grain Mites, Granary Weevils, Indian Meal Moths, Mediterranean Flour Moths (flying), Red Flour Beetles, Rice Weevils and Sawtoothed Grain Beetles:
Apply as a Crack & Crevice, direct spray, or space spray treatment into cracks and crevices/corners of pantries, cabinets, food processing and handling equipment and other places where insects harbor. Apply around cartons, containers and other areas where these insects tend to congregate.
Fleas in Buildings:
Hold product 36” above floor and direct spray toward floor and lower walls at the rate of 10 sec/100 ft2. Ensure that the underneath and lower surfaces of furniture are contacted. Keep area closed for 15 minutes. Open and thoroughly ventilate before reoccupying. Repeat treatment after 7 days if necessary.
Hold container 36” above the floor and direct spray toward pet beds and resting quarters, treating at the rate of 10 sec/100 ft2. Apply as a Crack & Crevice treatment into adjacent cracks and crevices such as behind baseboards and edges of carpet and floor covers. Treat higher cracks such as upper door jams and window framing, behind pictures and other areas where females may crawl to lay eggs.
Food Areas of Food Handling Establishments
Food handling establishments are places other than private residences in which food is held, processed, prepared or served.
Include areas for receiving, serving, storing (dry, cold, frozen, raw), packing (canning, bottling, wrapping, boxing), preparing (cleaning, slicing, cooking, grinding), edible waste storage and enclosed processing systems (mills, dairies, edible oils, syrups).
Include areas such as garbage rooms, lavatories, floor drains (to sewers), entries and vestibules, offices, locker rooms, machine rooms, boiler rooms, garages, mop closets and storage areas (after canning or bottling). Apply according to specific directions for pest(s) to be treated as specified in the Indoor Use section above. Do not make space spray applications to food areas when the facility is in operation. Prior to space spray applications, cover or remove exposed food and cover food processing surfaces, in the treatment area, or clean after treatment and before use.
Flies, Gnats and Mosquitoes - Ground Application:
Treat landscapes and open areas around residence, outer buildings and in campgrounds. Apply at a rate of 5 -15 sec/1,000 ft2. Apply in wide swaths across the area to be treated. Allow treatment to penetrate dense foliage. Best results are obtained when wind speed is 5 mph or less.
Bees, Flies, Cluster Flies, Clover Mites, Mud Daubers and Wasps:
Apply directly on insects and their nests from approximately 18”. Disperse into hiding and breeding places (voids) contacting as many insects as possible.
Used this to treat a yellow jacket nest. Already had the Tempo dust so only needed this. Sprayed it in the yellow jacket entrance for 15 seconds as instructed and sprinkled Tempo dust around the hole. Not a single yellow jacket came out during the process. The next morning there was no activity at the nest. Worked perfectly.
*remember to only treat a yellow jacket nest at night*