Yes, Talstar P can be used outdoors for kissing bugs, as well as various other pests as well. The mixing ratio is 1 fl. oz. per gallon of water.
Talstar P(Talstar One) will kill deer flies that come in direct contact with the treated surfaces.
Talstar P (Talstar One) can kill grasshoppers including lubbers.
You can use a hose-end sprayer to apply Talstar P. You shoul use 1 oz per 1000 sq ft, and we recommend using 1-3 gallons of water per 1,000 sq ft. Keep in mind that it is most important to use the correct amount of concentrate and then think of the water as a carrier, so it is better to use a bit more water than to use too little. For example, to treat half your yard, you would use 7.5 oz at a rate no higher than 1 oz per gal of water, but usually it is best to use a rate of 0.3 or 0.5 oz per gal of water with a hose-end sprayer. You can always start with a small area and test using just water to get an idea for how heavily you tend to spray and how fast you walk when spraying.
Talstar P is mixed at the rate of 0.5 to 1.0 fl oz per gallon of water, so a gallon of the Talstar will make about 128 to 256 gallons of solution and will last up to 90 days depending on where it is applied. Each finished gallon of solution covers approx 1000 sq. ft. Inside applications are limited to just cracks and crevices, along baseboards etc. Outside you would apply 2 to 3 feet up and out around the home, around window and door frames, and other potential entry points. You can choose to spray the lawn for further protection or just around the perimeter. Please refer to the product label for complete instructions on any target pest.
Talstar is a great option for mosquito control and can be used in either a mist blower or a sprayer.
Talstar P can be applied on the ground when there is a small amount of dew. Allow to fully dry prior to rain fall, 24 hrs.
Talstar P (Talstar One) is a great product to use for fungus gnat control. It is to be used inside and outside the home, but will only kill the adults as the larvae is protected in its egg form much like a chicken egg is protected until cracked. To control the larvae you would need to mix the NyGuard IGR (birth control) in with the Talstar. NyGuard is labeled for fungus gnats as well as a large variety of other insects to sterilize the adults from being able to lay viable larvae. This will control the population drastically in keeping new ones from developing. You should mix 1 ounce of Talstar P with 4 ml of NyGuard IGR to each gallon of water you use. Talstar P can be used as a broadcast over the entire lawn or just as a perimeter treatment. You will want to focus on the mulch bed area and the underside of shrubs, bushes, or trees in the area. It is completely safe to spray on ornamentals. In the garage area, spray as crack and crevice and focus on damp areas/reducing the water/moisture. Please let us know if you have any further questions.
We generally recommend using a pyrethroid such as Talstar P Professional Insecticide or Permethrin SFR as a preventative treatment in late spring/summer before egg hatch to protect trees. If trees are badly infested, then they should be removed and either chipped or burned.
Keep in mind that trees which become infested with bark beetles are almost always susceptible due to some other existing weakness such as drought or disease.
For outdoor use the Talstar P will be safe for animals of all kinds once dry. For indoor use if you have pet birds, we recommend removing the birds from the home while you treat and for at least 4-6 hours to give plenty of time for the product to dry and air out. Birds are more sensitive to chemicals and smells so keeping them out of the treatment areas for longer than pets like dogs and cats is recommended. If you have any safety concerns regarding its use around your birds please take info on the product to your birds vet for consultation.