Talstar P Professional Insecticide is a chemical so could have a reaction with the type of paint used on the sign. But there is really no way of knowing if it was the spray, paint, or age. Also, Talstar is not labeled to be sprayed on signs.
Yes, adult Japanese Beetles can be controlled using Talstar P. Thoroughly spray the foliage using 1 oz per gallon of water/1000 sq ft for best results. Talstar should not harm trees or shrubs if used according to the instructions on the product label.
Talstar P is safe for use on most plants. Having said that we still recommend you test the product on just one or two plants before using it on all of the plants to test for damage as some plants can be more sensitive than others.
Yes, Talstar works well for both the mature and the immature spider mites and can be used on spruce trees. Talstar provides optimal spider mite control when applied during spring to mid-summer. Higher application rates and/or more frequent treatments may be required for acceptable spider mite control during mid to late-summer. The addition of a surfactant or horticultural oil may increase the effectiveness of Talstar.
You should reapply the Talstar P once a month through the warm season for best results. Please note that Talstar P will not offer an instant knockdown of insects, it will take several minutes to a few hours for them to die after they come into contact with treated areas. We also recommend dusting the carpenter bee holes with a dust such as Tempo Dust to help kill any larva inside. Do not plug the holes for at least 30 days after dusting to prevent the developing larva from drilling a new whole to exit.
Yes, Talstar is labeled to be used indoors in the areas mentioned. Please make sure to follow full label instructions prior to application.
Talstar P is great for treating mosquitoes and can be applied in a hose end sprayer. You will mix one ounce per gallon of water per 1,000 sq ft.
Mosquito Control
No, Talstar P Professional Insecticide cannot be applied via a fogger. It can only be applied via a sprayer or mister. There are not many products that can be fogged outdoors & those that can do not leave a residual like Talstar does. Their residual tends to last as long as the fog is there but once it's gone so is the residual. Fogging is only really recommended prior to an event but not as a long term pest control remedy
Yes, Talstar P is odorless, dries clear, leaves no stains, is non-irritating to the skin, and will not break down easily with rainfall.
Talstar P Professional Insecticide is a great product for chinch bugs. Chinch bugs infest the base of grass plants and are often found in the thatch layer. Chinch bugs can be one of the most difficult pests to control in grasses and the higher applications rates will be required to control populations that contain both nymphs and adults during the summer. It may also be necessary to remove the thatch layer if it exceeds 1 inch in thickness to allow the Talstar to penetrate down to the soil. When treating for chinch bugs it is recommended that you do a second treatment 21-30 days after the first treatment. You will use 1 fl. oz. of product per gallon of water. This will treat 1000 square feet. Be sure to water the product in at least 0.5 inches after it has been applied.
Talstar P Professional Insecticide is not intended to be broadcasted on floors the way it is. We would recommend trying to remove the product with hot soapy water. If it was carpet, a shampooer with soap & water should be able to remove the residual from the floor.
Talstar P Professional Insecticide can be mixed with fertilizers so iron being in the water should not affect it. Where the water comes from should not make a difference in the efficacy of the Talstar or other chemicals, however if the water is extremely alkaline or acidic that could affect the products stability in the solution.
Talstar P Professional Insecticide cannot be fogged but should not harm artificial turf. However, since manufacturers have likely not tested on artificial turf it is recommended to test on a small area first
Unfortunately, there is no easy solution when it comes to pine beetles. Infected trees should be cut down (before the newly hatched beetles fly out of the trees in the spring/summer) and the wood burned or chipped, while other still healthy trees should be sprayed annually to protect them. Because of the natural boring behavior of the beetle, they are protected from topically applied insecticides, and systemic insecticides (those injected into the tree or applied as a root drench) have proven ineffective for pine beetle infestations. Healthy trees can be protected before the beetles attack by topically spraying them with a synthetic pyrethroid like Talstar. The tree should be sprayed from the ground to 15 ft up the trunk to prevent future infestations. You should contact your local cooperative extension office to find out the best time to start spraying in your region.
Per the Talstar P label, when applying mixed solution, the applicator needs to wear shirt, shoes, socks, pants and waterproof gloves. If applying in a non-ventilated area, applicator will need to wear a resperatory mask. You may look at our Basic Safety Kit for the necessary protective gear.
You can apply as a crack and crevice treatment and to baseboards as mentioned. It is also approved for "spot spray to areas where pests hide, such as baseboards, corners, storage areas, closets, around water pipes, doors and windows, attics and eaves, behind and under refrigerators, cabinets, sinks, furnaces, stoves, the underside of shelves, drawers and similar areas." It would not be suspected to stain carpet, however, you can always perform a spot test in an inconspicuous area if needed.
