Emergency Bed Bug Kit

Before applying any chemicals, it is crucial to prepare the area for treatment by removing clutter, vacuuming, steaming (optional), and encasing mattresses and box springs. Taking time for these preparation steps will make your treatments much more successful. Using the products in your Bed Bug Kit, treat all cracks, crevices, voids, tufts, seams, and folds where bed bugs may be found. Always keep pets, children, and other people out of the treatment area until the products have dried - usually about an hour.

STEP 1 - Spray - Crossfire Aerosol

*Wear gloves when mixing and handling pesticides, such as Nitrile Chemical Resistant Gloves.

*Shake Crossfire Aerosol vigorously before each use. You may use the open nozzle for treating broader areas, or use the crack and crevice straw for more detailed spraying.

*Pressure will be high when the can is full, so hold the can 8-12 inches away from the surface when applying as a spot spray.

*Apply Crossfire Aerosol to the following areas, contacting as many bugs and eggs directly in these areas as possible:

• Around bed and furniture legs - Inspect wheels, casters, posts, and legs of all furniture.
• Behind wall fixtures
• Under floor lamps
• Cracks and crevices along baseboards and floor moldings
• Beneath floor coverings and along the edges of wall-to-wall carpeting
• On infested mattress and box springs - Remove linens, then apply to tufts, seams, folds and edges.
• Cracks and joints in bed frames, headboards, dressers, shelves, and other furniture
• Picture frames and wall coverings - Remove from the wall and treat cracks and crevices on and behind these items.
• Around door frames, window frames, and thresholds
• Upholstered furniture - Apply only to the infested tufts, seams, folds, and edges, but do not apply to flat surfaces where prolonged human contact will occur.

*Do not remake beds or replace items on shelves or in drawers until spray has dried.

*Do not apply as a space spray or broadcast treatment to floors, floor coverings, mattresses, or other furniture.

STEP 2 - Dust - Bellow Hand Duster and CimeXa Insecticide Dust

*Once your spray application has dried, you can apply the insecticide dust.

*Using insecticide dust can be very messy, so be sure to wear gloves and consider having a moist paper towel handy to clean up excess dust.

*To fill the Bellow Hand Duster, remove the black rubber stopper on top of the duster. Gently unscrew the white top of the CimeXa dust, then slowly tap the dust into the duster. Fill the duster up to halfway (or less), so there is plenty of room for the dust to move inside the duster.

*You may want to add a few small objects such as coins, pebbles, or marbles to prevent clumping inside the duster.

*Replace the black stopper so that it fits snugly into the opening. Remove the black rubber cap from the end of the extension wand. To apply dust, hold the duster upside down, so that the extension wand is on top, then gently squeeze the bellows between the thumb and fingers.

*Apply CimeXa Dust to voids and other hidden areas where it will not be disturbed, such as:

• Behind electrical faceplates - Remove switch and electrical plates to gain access to wall voids.
• Along baseboards - Treat any cracks in, above, or below baseboards where the tip of the duster will fit. Also treat under the edges of carpeting where you are able.
• Headboards - Remove from the wall or dismantle to allow thorough treatment.
• Drawers and furniture - Remove drawers and treat along tracks and support, as well as the corners and edges of the cabinet. Also treat in cracks and crevices on the undersides of cabinets and other furniture, and in any hollow areas such as bed frame tubing.
• Box Springs and upholstered furniture - Check for tears in fabric backing or other hollow areas where the tip of the duster may fit, and treat these areas.
• Behind wall fixtures - Remove fixtures from walls and treat behind each one.

*Be careful to avoid over-dusting. CimeXa Dust is very fine, and it only takes an extremely small amount to kill a bed bug.

*If dust escapes into open areas, simply wipe up the excess dust with a moist paper towel.

*Do not apply dust as a broadcast or in open areas where it will be moved around as it can become an irritant.

STEP 3 - TREAT CLOTHING AND LINENS

*Although this step does NOT involve any chemicals in your kit, it is a crucial part of your treatment.

*Clothing, linens, or other fabric items in the infested rooms should be removed in bags, then washed and dried or dry cleaned.

*Do not return items to the infested areas until there has been no evidence of bed bugs for 30 days.

*Failure to make sure all items being returned to the room are bed bug-free may cause a re-infestation.

*Objects that cannot be washed can be put into a bag or bin with a Nuvan Pro Strip to eliminate bed bugs. The items must stay sealed for 4 weeks in the bag or bin. If this treatment will not work for you because of the time it takes to eliminate the bed bugs you also have the option of using a bed bug heater like the ZappBug Heater. Place your items inside the unit where they will be heated up to 155 degrees Fahrenheit. Within a few hours, all bed bugs will be killed.

STEP 4 - REPEAT! REPEAT! REPEAT!

*Repeat Step 1 (Crossfire Aerosol) every 21 days until no one is getting bitten any longer, and there is no further evidence such as live bugs, cast skins or fresh blood spots found. This is absolutely crucial! Depending on the severity of the infestation it can take a minimum of 7-8 weeks, including repeat treatments. Failure to be thorough can prolong the bed bug control process and can make it harder to eliminate them.