No, Drive XLR8 Herbicide Crabgrass Killer is not labeled for nutsedge. Please review our Nutsedge Treatment Guide for information and product recommendations.
It is recommended to use a Methylated Seed Oil Surfactant like Duo Stick with Drive XLR8 Herbicide Crabgrass Killer for best results. This helps the herbicide stick to the weed surfaces for better adhesion and faster burn down.
Drive XLR8 herbicide is not labeled for use on alfalfa so it will likely kill it. Instead, you may use a non selective product such as AXXE Broad Spectrum Herbicide while the alfalfa is dormant. Please be sure to review the product label for more information and complete application instructions.
Drive XLR8 is not labeled to treat panic veldt grass. Using a glyphosate product (Roundup) applied as a foliar spray at 2 percent concentration with added surfactant was shown to be effective against Panic-Veldt. Using a product like Roundup QuickPRO will give you both treatments in one. QuickPRO has two active ingredients: 73.3% glyphosate and 2.9% diquat. The addition of diquat, along with the surfactant, gives you even faster burndown. It controls broadleaf and grass weeds, or woody brush and trees - roots and all.
Using a chemical method along with chemical treatment, will help with control unless you are able to to identify where this weeds originates. Regardless of the method used, more than one year of treatment will be necessary, due to its extensive seedbank, the persistence of which is unknown. You may also contact your local master gardener for recommendations that have worked in your area. Click here for the link.
Drive XLR8 is for turfgrass areas only and cannot be used on ornamentals, flowers, or landscape beds where Bifen IT is also labeled for lawns but also commonly applied to treat insects as a foliar spray to bushes, trees, shrubs, etc. Be mindful that you are only applying your herbicide in the correct areas.
Herbicides and insecticides can be tank mixed together in a tank mix as long as there are no tank mixing restrictions on the product label for the other product that you are using. We recommend performing a small jar test for compatibility any time you are using two new products together for the first time.
Please view our Tank Mixing Herbicide Video showing how to do a “Jar Test”.
Drive XLR8 can take up to 3 weeks to see full results on targeted weeds and a second appliation may be needed for more established weeds. Keep in mind, for best results, applications should be applied to listed weeds when they are young and actively growing and temperatures are between 65-85 degrees. For actively growing crabgrass, Drive XLR8 is mixed at 1.45 fl oz per 1000 sq ft along with adding 0.16 - 0.48 fl. oz Duo Stick per gallon of water. If only treating 500 sq ft, you would cut those rates in half, mixing Drive XLR8 at 0.72 fl oz in one gallon of water along with the 0.16 to 0.48 fl oz of Duo Stick Surfactant.
It is important to follow the recommended rates per the product label and not overmix or overtreat to avoid burning or injury to your turfgrass. You may see some discoloration, burning or wilting of your turfgrass as the rate applied of 2 fl oz Drive + 1 fl oz Surfactant over 500 sq ft is double the labeled rate.
Drive XLR8 an be applied 7 days or greater prior to seeding and up to 28 days after emergence of Kentucky Bluegrass. Please view the full product label for more information.
Yes. To avoid any turf damage, Drive XLR8 should be applied when temperatures are between 65-85 degrees. It would be best to apply in the early morning or in the evening so that the product has sufficient time to dry before temperatures get above this range.
It is recommended to use a Methylated Seed Oil Surfactant with Drive XLR8 for best results. Please view the product label for mix rates and more information.
Drive XLR8 should NOT be applied in vegetable gardens or where edible vegetation is grown (or areas intended for planting). Any treated edibles should be discarded.
Hi-Yield Grass Killer is labeled to treat grassy weeds and safe for Vegetables, Gardens, Trees, Shrubs, Ornamentals and ground covers. Please view the full product label for more information.
Drive XLR8 is applied at 63 fl oz in 20 gallons of water to cover 1 acre (add a MSO or equivalent to the mix for more effective control-we offer Duo Stick or DyneAmic).
Please refer to the product label for full application instructions here.
How long you will need to wait to make an application of Drive XLR8 will depend on the type of turfgrass you are overseeding with.
Please refer to Table 4 on page 10 of the product label to view the Seeding/Overseeding/Sprigging Timing Chart to help determine the correct timing for your needs.
Drive XLR8 Herbicide Crabgrass Killer is only a post emergent herbicide and will only kill actively growing weeds. To prevent new crabgrass from germinating, a pre-emergent needs to be applied when soil temperatures are around 55 degrees.
Dimension 2EW is one of the most successful pre-emergents for crabgrass prevention.
Click HERE to view How to Get Rid of Crabgrass Treatment Guide
We typically recommend waiting atleast 24 hours up to 7 days in between applying herbicides and fertilizers to avoid overstressing the turfgrass unless previous applications have shown tolerance to using a fertilizer and herbicide together.
The Drive XLR8 Herbicide Crabgrass Killer does advise that a liquid nitrogen fertilizer can cause some yellowing therefore a small test application would be recommended if deciding to tank mix.
Please review the product label for tank mixing instructions prior to mixing in your sprayer.
Drive XLR8 Herbicide Crabgrass Killer is only available in a half gallon.
QuinKill Max Crabgrass and Weed Killer uses the same active ingredients as Drive XLR8 and comes in a 16 oz and 32 oz size bottle for smaller quantities.
Drive XLR8 Herbicide Crabgrass Killer states on the product label DO NOT irrigate the area for 24 hours after the application. If rainfall does not occur 2-7 days after the application, irrigation of at least 1/2 inch of water is desirable.
Please view the prodcut label for more information.
There is not a specific amount of time you need to wait to apply your fertilizer after applying Drive XLR8 Herbicide. Since Drive works best when it has at least 24 hours to dry after application, then waiting at least 1 day before watering or applying a liquid fertilizer would be advantageous.
Yes, you can use a pull behind sprayer to apply Drive XLR8. It is applied at 1.45 fl. oz. per gallon of water per 1000 sqft or 63 fl oz in at least 20 gallons of water to cover 1 acre (add a MSO or equivalent to the mix for more effective control-we offer Duo Stick or DyneAmic).
Drive XLR98 Herbicide is applied at 64 fl oz per acre tank mixed with 8.5 oz (50 tsps) of a Methylated Seed Oil Surfactant in no less than 20 gallons of water per acre.
Plese view a quick video on How to Apply Drive XLR8 Herbicide and the product label for more information.
Drive XLR8 Herbicide Crabgrass Killer is not labeled to be used around Asiatic Jasmine however we do have Grass Out Max Herbicide that is labeled to treat grassy weeds in Asiatic Jasmine as well as most landscape, home and garden, ornamental, agricultural and non-crop uses.
You can view the full list of tolerant ornamentals on the product label.
