-
Asked by Luis from San Juan Pr01/15/2015QHow many ounces of Basagran T/O per gallon of water for spot spray in an established lawn?A
This mixing rate of Basagran T/O depends on big of an area you are wanting to spot treat. Please refer to the Mixing Table on page 4 of the Basagran T/O label. The label also warns that applying this product as a spot treatment can result in excessive dosage and possible turf injury. Area to Be Spr…
Read Full Answer »This mixing rate of Basagran T/O depends on big of an area you are wanting to spot treat. Please refer to the Mixing Table on page 4 of the Basagran T/O label. The label also warns that applying this product as a spot treatment can result in excessive dosage and possible turf injury. Area to Be Sprayed / Amount of Basagran T/O / Amount of Water 200 sq ft / 1 teaspoon Basagran T/O / 0.2-0.4 gallons of water 400 sq ft / 2 teaspoons Basagran T/O / 0.4-0.6 gallons of water 1,000 sq ft / 5 teaspoons Basagran T/O / 1-2 gallons of water 1 acre / 2 pints of Basagran T/O / 40-80 gallons of water Sprayer Calibration Suggestions / Hand Sprayers: 1. Stake off a 400 square foot area of turf for practice. This is an area 20’ (7 steps) x 20’. 2. Add a measured quantity (1.5 gallons for example) of water to the sprayer and uniformly spray the 400 square foot area. Measure water remaining to determine the amount applied per 400 square foot area. (Note: A minimum of 3 pints per 400 square feet is recommended). 3. Prepare the spray solution according to Table 1. Application Rates for Turf. Example:Assume that in Step 2 the 400 square foot area was uniformly covered with 0.5 gallon of water. Referring to the table, add 2 teaspoons of Basagran T/O per 0.5 gallon of water for each 400 square foot of turf to be sprayed. (Note: Using this mix to spot spray individual weeds may result in an excessive dosage and possible turf injury.) -
Asked by Arthur from Lincoln, Ri07/27/2012QWhat oil and at what concentration to use with Basagran T/O Herbicide
What oil and at what concentration to use with Basagran T/O Herbicide?AWhen an herbicide calls for oil, it is referring to a surfactant. Surfactant helps the herbicide stick to the waxy coating of the weeds and lawn you are applying it to. It improves the effectiveness of herbicides greatly.
-
Asked by Earl from Sneads Ferry Nc04/02/2013QIs Basagran safe to use on St Augustine grasses?A
Basagran T/O Herbicide is labeled to be used on St Augustine grass. Be sure to read and carefully follow the product label for best results.
-
Asked by Pat from Oklahoma01/28/2018QHow much Basagran T/O Herbicide do I use per gallon of water?
I have 3 acres that is getting infested with yellow nutsedge and I have a 25 gal pull behind lawnmower sprayer. Not sure how much Basagran to buy.APer the Basagran T/O Herbicide Product Label: For yellow nutsedge, apply no more than 0.75 fluid ounces per 1,000 square feet (2 pints per acre) at one time. Make a second application 10-14 days later. Apply no more than 1.5 fluid ounces per 1,000 square feet (4 pints per acre) in one season. On…
Read Full Answer »Per the Basagran T/O Herbicide Product Label: For yellow nutsedge, apply no more than 0.75 fluid ounces per 1,000 square feet (2 pints per acre) at one time. Make a second application 10-14 days later. Apply no more than 1.5 fluid ounces per 1,000 square feet (4 pints per acre) in one season. On average you will use 40-80 gallons of water per acre depending on lawn thickness and weed size/growth stage. -
Asked by Howard from Morriston, Fl08/09/2016QHas Basagran T/O Herbicide been tested on Creeping (Asian) Dayflower?A
The product label does state: Weeds controlled by Basagran T/O in turf include annual sedges, yellow nutsedge, wild mustard, dayflower, common groundsel, and common purslane. While it does not specific Creeping Dayflower exactly we do not know if has been tested against it and would recommend che…
Read Full Answer »The product label does state: Weeds controlled by Basagran T/O in turf include annual sedges, yellow nutsedge, wild mustard, dayflower, common groundsel, and common purslane. While it does not specific Creeping Dayflower exactly we do not know if has been tested against it and would recommend checking directly with the manufacturer for further information. BASF can be reached at 800-777-8570. -
Asked by Dwight from Huntsville, Al05/01/2016QCan Basagran T/O Herbicide be used in a vegetable garden? Is there a waiting period before you can plant?
The main product used for weeds in a vegetable garden is a Roundup type product, like our RoundUp QuickPro product. Roundup Professional products do not leave a residual that could possibly be soaked up by the roots of your garden. Of course you do not want to get the RoundUp product on any plants you want to keep. You should only direct it at the weeds you want to get rid of. You can plant in the area treated 2 weeks after application.ABasagran T/O Herbicide is only labeled to be used in non-cropland areas so would not be used in a vegetable garden. The main product used for weeds in a vegetable garden is a Roundup type product, like our RoundUp QuikPro product. Roundup Professional products do not leave a residual that could …
Read Full Answer »Basagran T/O Herbicide is only labeled to be used in non-cropland areas so would not be used in a vegetable garden. The main product used for weeds in a vegetable garden is a Roundup type product, like our RoundUp QuikPro product. Roundup Professional products do not leave a residual that could possibly be soaked up by the roots of your garden. Of course you do not want to get the RoundUp product on any plants you want to keep. You should only direct it at the weeds you want to get rid of. You can plant in the area treated 2 weeks after application. -
Asked by Dave from Spring Hill, Fl02/25/2018QWhy was the size of Basagran restricted? Buying a gal is overkill!
I used to buy a pint about once every 2 years, now I have to buy a gallon? That makes no sense as it may cause consumers to overuse this product instead of under-use. If EPA was smart they'd allow only 1/2 pint sales. This is the ONLY product that kills my yearly nutsedge!AWe do apologize but we have no control over when manufacturers discontinue products like the Southern Ag Basagran. We would recommend using Sedgehammer for nutsedge which works very well and is in small amounts.
-
Asked by Watson from Pocomoke, Md07/22/2021QCan Basagran be used to control yellow nutsedge in Liriope grass?A
Basagran T/O Herbicide may only be used on the following established turfgrass species: bahiagrass, bentgrass, bermudagrass, bluegrass, buffalograss, carpetgrass, centipedegrass, fescue, ryegrass, St. Augustinegrass, seashore paspalum, and zoysiagrass as well as lilyturf, big blue lilyturf and cre…
Read Full Answer »Basagran T/O Herbicide may only be used on the following established turfgrass species: bahiagrass, bentgrass, bermudagrass, bluegrass, buffalograss, carpetgrass, centipedegrass, fescue, ryegrass, St. Augustinegrass, seashore paspalum, and zoysiagrass as well as lilyturf, big blue lilyturf and creeping liriope for control of yellow nutsedge. Image Kills Nutsedge can be used over established Giant Liriope and Variegated Liriope, per the product label.
-
Asked by Dale from Coral Springs09/09/2021QAny temperature restrictions on using Basagran T&O Herbicide?A
Per label DO NOT apply Basagran T/O Herbicide to turfgrass that has been under stress such as drought, cold temperature, or injury from other herbicides or pesticides. It best applied when applied temperatures above 55 and below 85.
-
Asked by Mike from West Memphis, Ar.08/29/2021Qmixing instructions per gallon for Basagran sedge controlA
Read Full Answer »
Per the Basagran T/O Herbicide Product Label: For yellow nutsedge, apply no more than 0.75 fluid ounces per 1,000 square feet (2 pints per acre) at one time. Make a second application 10-14 days later. Apply no more than 1.5 fluid ounces per 1,000 square feet (4 pints per acre) in one season.&n…
Per the Basagran T/O Herbicide Product Label: For yellow nutsedge, apply no more than 0.75 fluid ounces per 1,000 square feet (2 pints per acre) at one time. Make a second application 10-14 days later. Apply no more than 1.5 fluid ounces per 1,000 square feet (4 pints per acre) in one season.
On average you will use 40-80 gallons of water per acre depending on lawn thickness and weed size/growth stage.
This mixing rate of Basagran T/O depends on big of an area you are wanting to spot treat. Please refer to the Mixing Table on page 4 of the Basagran T/O label. The label also warns that applying this product as a spot treatment can result in excessive dosage and possible turf injury.
Area to Be Sprayed / Amount of Basagran T/O / Amount of Water
200 sq ft / 1 teaspoon Basagran T/O / 0.2-0.4 gallons of water
400 sq ft / 2 teaspoons Basagran T/O / 0.4-0.6 gallons of water
1,000 sq ft / 5 teaspoons Basagran T/O / 1-2 gallons of water
1 acre / 2 pints of Basagran T/O / 40-80 gallons of water
Sprayer Calibration Suggestions / Hand Sprayers:
1. Stake off a 400 square foot area of turf for practice. This
is an area 20' (7 steps) x 20'.
2. Add a measured quantity (1.5 gallons for example) of water to the sprayer and uniformly spray the 400 square foot area. Measure water remaining to determine the
amount applied per 400 square foot area. (Note: A minimum of 3 pints per 400 square feet is recommended).
3. Prepare the spray solution according to Table 1. Application Rates for Turf.
Example:Assume that in Step 2 the 400 square foot area was uniformly covered with 0.5 gallon of water. Referring to the table, add 2 teaspoons of Basagran T/O per 0.5 gallon of water for each 400 square foot of turf to be sprayed. (Note: Using this mix to spot spray individual weeds may result in an excessive dosage and possible turf injury.)
-
Asked by Mike from Sidney, Oh06/13/2019QCan you mix Basagran T/O Herbicide with Triplet to control sedge and broadleaf combined?A
BASF does not recommend using Basagran T/O tank mixes other than those listed on BASF labels, supplemental labeling, or technical bulletins. Triplet SF Selective Herbicide also contains dicamba so would not fall under an approved tank mix. It would be best to make separate applications.
-
Asked by Kelly from 5 South Ridgeview Road, Stuart Fl08/02/2018QCan Basagran 5l be used on st augustine lawns or must you use the Basagran T/O Herbicide?A
Basagran T/O Herbicide is labeled to be used on St Augustine grass. Be sure to read and carefully follow the product label for best results. Since we do not carry Basagran 5L, we recommend contacting the manufacturer for any questions regarding that particular product. BASF 1-800-777-8570.
-
Asked by Mathies07/11/2018QWhat is the difference between Basagran T/O an Southern Ag Basagran Sedge Control?A
The difference between the Basagran T/O Herbicice and the Southern Ag Basagran Sedge Control is their manufacturer. Both products contain the same active ingredient with the same percentage amount, but one is made by BASF and the other is made by Southern AG. Also the Southern Ag Basagran Sedge Con…
Read Full Answer »The difference between the Basagran T/O Herbicice and the Southern Ag Basagran Sedge Control is their manufacturer. Both products contain the same active ingredient with the same percentage amount, but one is made by BASF and the other is made by Southern AG. Also the Southern Ag Basagran Sedge Control has been discontinued and no longer available through us. -
Asked by Stanislaw from Providence Forge, Va02/28/2018QIs Basagran safe for over the top spraying of iris beds to control post-emergent broadleaf weeds?A
Basagran T/O Herbicide does not list iris on the label as tolerable for over the top spraying. Bonide Chickweed, clover, and Oxalis Killer RTU can be used to spot treat around the Iris for the listed weeds on the product label.
-
Asked by Bob from Naples, Fl06/09/2017QIs Basagran T/O Herbicide safe to use on Floratam St. Augustine grass?A
The product label for Basagran T/O Herbicide states that it can be used on St.Augustine and does not mention any restrictions for the Floratam species. It should be safe to use if applied according to the instructions on the label.
-
Asked by Linda from Charlotte, Nc08/20/2022QWill BasagranT/O harn dayliliesA
As stated on the product label, Basagran T/O may be applied as an Over-The-Top application to daylily. Please be sure to review the product label for more information and complete application instructions.
-
Asked by Elio from Visalia, Ca06/22/2022QCan Basagran T/O Herbicide be shipped to California?A
We apologize that we are unable to ship Basagran T/O Herbicide to California and Alaska at this time due to restrictions. Please let us know if we can help with anything else.
-
Asked by Alan from Debary, Fl04/01/2022QHow soon after applying Basagran T&O Herbicide can I reseed my bahiagrass lawn?A
Per the product label, it is recommended to wait 30 days after applying Basagran T/O Herbicide to seed areas.
-
Asked by Arsen from Daytona, Florida04/03/2024QDoes Basagran kill signal grass in St augustine?A
Basagran T&O Herbicide is not labeled to treat signalgrass.
-
Asked by Andy from Hampshire Il07/16/2021QWhat is the residual on Basagran T O?
For use in Nursery production. Can I plant on soil 2 weeks after application? For deciduous and evergreen production.APer the manufactuer, Basagran T&O herbicide has little soil residual activity. For a more specific residual time, we recommend contacting the manufacturer directly at 800-327-4645.