Price/Ea.
$28.55
Buy 2 or more: $26.53 each
Have a Question? Ask Our Pros!
Email Our Pros
We're here to help
Offline. Leave Us a Message
You May Also Need
-
Product Overview
Hi-Yield Stump Remover is a product that decomposes the stump from the inside out. Hi-Yield Stump Remover makes the stump porous through out so that removing or burning is easier to do. Use the directions on the label for diagrams of where to drill holes in the stump for proper application. Hi-Yield Stump Remover will not harm surrounding vegetation.
-
Details
Active Ingredient Sodium Metabisulfite 100% Target pests Nuisance and unsightly stumps Application * See label for complete application instructions (proper drilling and illustrations on stump removal) Pet safe Yes, if used as directed on Label Shipping Weight 1.66 lbs Manufacturer VPG (Mfg. Number: 32015) UPC 732221320154 DIRECTIONS FOR USE
Use this to remove nuisance and unsightly stumps. HI-YIELD STUMP REMOVER decomposes the wood of tree stumps leaving them porous. The decomposition, depending on the size of the stump, may take several weeks or months. This allows for easy removal or burning of the stump. HI-YIELD STUMP REMOVER is harmless to vegetation surrounding treated stumps. For removal of stumps up to 12” in diameter, drill a 1” hole in center of stump approximately 10” to 12” deep. Drill an additional 1” hole into the side of the stump approximately 3” below the top of the stump. This second hole should be slanted to connect (or nearly so) with the bottom of the center hole. Drill several sets of such holes for stumps larger than 12” wide.
Pour approximately 4 oz. of HI-YIELD STUMP REMOVER into each hole. It works best when weather is warm and stumps are dry. Fill each hole with water. Allow to stand from four to six weeks.If stump is to be burned, refill holes with kerosene or fuel oil. Allow sufficient time for the liquid to be completely absorbed into the stump.
Then apply a slight amount of kerosene over stump and ignite. Or burn charcoal on top of stump or around base to start stump burning. The stump will burn with a smoldering, red glow, clear down to the roots, disintegrating the stump into ashes.
-
Product Documents
-
6 Customer Reviews
Top Reviews
Time needed
By Hgc on 11/26/2016
Decomposition of a stump takes time. Several applications --of this or any priloduct, even straight nitrogen-- are needed. No change will be visible for at least a few months. After that, progress is …
Read Full Review »
DOSE NOT WORK
By Ron on 05/11/2016
It was applied 4 weeks ago and no indication of any decomposing on my two tree stumps.
This is a long process .
By Ted on 07/29/2018
This will take years to work as described. It may not be much less expensive than having the stump removed by pros. I add more product when the level goes down. I started about 100 days ago. I do beli…
Read Full Review » -
5 Questions & Answers
Helpful Q&A'sQHow long does complete decomposition take when using Hi-Yield Stump Remover?juniper stumps approximately 10 inches in diameterAIt will take 4-6 weeks to see full results. Please note that using the Stump Remover product will degrade the stump so that it is easy to burn or remove. Please read over the full product label for be…
Read Full Answer »It will take 4-6 weeks to see full results. Please note that using the Stump Remover product will degrade the stump so that it is easy to burn or remove. Please read over the full product label for best results.QWill Hi-Yield Stump Remover work on very large tree stumps?I had very large silver maple taken down and it has stump that is about 2ft radius will this work on something that size?AHi-Yield Stump Remover is labeled to work on stumps larger than 12 inches but you will need to drill additional holes. You can read the full directions here: product label instructions
QHow do you mix Hi-Yield Stump Remover?AOnce you've drilled holes into the stump as specified by the label, you will pour approximately 1/4 lb. of Hi-Yield Stump Remover into each hole. Fill each hole with water and allow it to stand fr…
Read Full Answer »Once you've drilled holes into the stump as specified by the label, you will pour approximately 1/4 lb. of Hi-Yield Stump Remover into each hole. Fill each hole with water and allow it to stand from four to six weeks.
