-
Asked by Joe from Henderson, Tx09/23/2021QDo I need to treat the entire plywood subfloor with Bora-Care or just the perimeter only?
Newly built Peer & Beam home, non-conditioned crawl space, plywood flooring with closed cell foam under floor. Do I treat entire plywood subfloor or perimeter only?AIf you are using Bora-Care as a preventive you will treat any raw untreated wood that you believe may be vulnerable to termite damage. If you are treating an active infestation you will need to apply it to all raw untreated wood where you have termite activity. Typically a full sub floor treatment…
Read Full Answer »If you are using Bora-Care as a preventive you will treat any raw untreated wood that you believe may be vulnerable to termite damage. If you are treating an active infestation you will need to apply it to all raw untreated wood where you have termite activity. Typically a full sub floor treatment would not be necessary for a house on a crawl space but we also recommend having some other termite prevention in place like termite bait stations or a termite trench treatment. -
Asked by Ibon from Ripon, Ca09/29/2021QCan we apply BoraCare to AAC block walls? These are more porous than standard concrete blocks.
In the tech bulletin it says BoraCare can be applied to concrete blocks. The AAC (aerated autoclaved concrete) blocks we are using are more porous than the usual concrete blocks. I'm assuming that means the BoraCare will penetrate better into these blocks. Am I correct?AYes, Bora-Care can be applied to concrete blocks, block or brick on the interior of crawl spaces and basement foundations as well as sill plates, piers, girders, subfloors, floor joists and any wood exposed to vertical access above ground. This is done typically to prevent shelter tubing by subt…
Read Full Answer »Yes, Bora-Care can be applied to concrete blocks, block or brick on the interior of crawl spaces and basement foundations as well as sill plates, piers, girders, subfloors, floor joists and any wood exposed to vertical access above ground. This is done typically to prevent shelter tubing by subterranean termites. For specifics on the absorbption into AAC (aerated autoclaved concrete), we would recommend contacting the manufacturer directly Nisus at 800-264-0870 for technical information. -
Asked by Randy from Saint Rose, La10/04/2021QBora Care or Bora Care with mold treatment
Which one do i use? After my house being devastated by Hurricane Ida I'm in the process of gutting it. I have some mold and termite damage on the 2x4's behind the sheet rock in the walls and some mold and termite damage on some of the 2x6's on the attic beams. Can I just spray what you recommend on the wood without cleaning? ThanksAIf you have termite activity and mold, you will need to make an application of Bora-Care first and once it's dry, then make an application of Bora-Care with Mold-Care. If you no longer have termite activity but would like to make a preventative treatment, we would recommend the same treatment if…
Read Full Answer »If you have termite activity and mold, you will need to make an application of Bora-Care first and once it's dry, then make an application of Bora-Care with Mold-Care. If you no longer have termite activity but would like to make a preventative treatment, we would recommend the same treatment if it is a preventative treatment where subterranean termites are involved. If you are only concerned with a preventative treatment for drywood termites then you can treat with Bora-Care with Mold-Care. -
Asked by Tina from Ny10/21/2021QCan I apply Bora-Care to wood with mildew stains?
I won't have time this fall to do the full clean and protective stain, but I can fit in a round of Bora-Care. The wood siding however shows mildew, but does not repel any liquid. Would it be okay to use Bora-Care now, then wash and stain the siding next year? So it is at least protected from bugs?ABora-Care does not treat mold. You will want to remove stains first, then treat with Bora-Care with MoldCare application once dried then stain and seal exterior wood as directed for the best application for treating/preventing wood destroying insects and mold/mildew. We do offer Mold Clean that c…
Read Full Answer »Bora-Care does not treat mold. You will want to remove stains first, then treat with Bora-Care with MoldCare application once dried then stain and seal exterior wood as directed for the best application for treating/preventing wood destroying insects and mold/mildew. We do offer Mold Clean that can be applied to remove stains with minimalizing or eliminating scrubbing and it penetrates deep into wood pores for thorough stain removal, which bleach cannot do. -
Asked by Jk from Los Angeles10/23/2021QCan Bora-Care be used to treat termites found on wood shelves used to grow for Tillandsia (air plants)?
Does this need to be sealed with a water sealant product due to watering the Tillandsia daily? Will the leashed chemical damage the plants?AIf wood treated with Bora-Care will be exposed to moisture such as watering or rainfall, then yes, you want to apply a water sealant after the Bora-Care application is dry. Boracare would not bother plants if they are in containers on top of the treated wood; however, any Boracare that contac…
Read Full Answer »If wood treated with Bora-Care will be exposed to moisture such as watering or rainfall, then yes, you want to apply a water sealant after the Bora-Care application is dry. Boracare would not bother plants if they are in containers on top of the treated wood; however, any Boracare that contact desirable plants directly may damage those plants. -
Asked by Jan10/26/2021QIf my crawl space is be sprayed with BoraCare, do I need to vacate the house for the night?A
No, vacating the home is not required when using Bora-Care in the home as this is considered a “green” product. Once the application has completely dried which usually takes about an hour or so depending on outside temperatures, humidity, etc, it would be fine to be in the home and sleep.
-
Asked by Betty from Scottsdale, Az10/29/2021QWhat happens if Bora-Care is applied directly and not diluted with water?A
Boracare should not be applied undiluted at any time and requires to be diluted with water in order to work properly and have the ability to absorb throughout the wood being treated. Boracare and the glycols it contains are designed to replace the natural moisture content of the wood so it bonds a…
Read Full Answer »Boracare should not be applied undiluted at any time and requires to be diluted with water in order to work properly and have the ability to absorb throughout the wood being treated. Boracare and the glycols it contains are designed to replace the natural moisture content of the wood so it bonds and last long term in the piece of timber you are trying to protect. -
Asked by Vm11/05/2021QCan Boracare be sprayed in a crawl space of a 104 year old home for powder post beetles during the rainy months in the Pacific Northwest or is it better to wait for warmer and drier weather?
I have a pest company treating the crawlspace for powder post they will be using a sprayer truck with about 15 gallons of water. My concern is with the rainy and cold weather the relative humidity will be too high to effectively dry the wood some members are over 100 years old and have some dry rot or age. Is it best to postpone this treatment when it is warmer and drier? Do not want a lot of moisture in the crawl for too long. It's vented crawl about 1500 sq ft?AIf the crawlspace is well vented it should be able to dry out after a Boracare application. Boracare is designed to absorb into and bond with the wood itself, using the glycols of the Boracare to penetrate all the way into the wood and replacing its natural moisture content with the borate particle…
Read Full Answer »If the crawlspace is well vented it should be able to dry out after a Boracare application. Boracare is designed to absorb into and bond with the wood itself, using the glycols of the Boracare to penetrate all the way into the wood and replacing its natural moisture content with the borate particles. You could run a box fan or small dehumidifier under there for a week if you wanted to try to help reduce moisture further, but you shouldn't have to worry about the higher humidity with the rain impacting it greatly. If you wanted to be absolutely certain you could wait until warmer/dryer weather, but it wouldn't be necessary. -
Asked by Ronald from Decatur, Il11/19/2021QIf overspray occurs while applying Bora-Care, is it necessary to clean those surfaces in which people may come into contact with?A
Bora-Care can be applied by spraying, painting or brushing onto surfaces. In areas where overspray is a concern, it is recommended to cover any unwanted areas or apply the treatment by brushing or painting directly onto the surface. If overspray should occur, you will need to clean and wipe those …
Read Full Answer »Bora-Care can be applied by spraying, painting or brushing onto surfaces. In areas where overspray is a concern, it is recommended to cover any unwanted areas or apply the treatment by brushing or painting directly onto the surface. If overspray should occur, you will need to clean and wipe those surfaces to remove any residual. -
Asked by Jean from Auburn11/21/2021QCan Bora-Care be used on an untreated beam where we are seeing several small holes before we stain and seal the beam? We will be using this for a fireplace mantel.A
Bora-Care can be used on untreated beams prior to staining, sealing or painting for both active and preventative treatments for wood destroying insects. For curative treatments, apply at a 1:1 ratio, for preventative treatments apply at a 5:1 ratio. Wait for the application to completely dry before…
Read Full Answer »Bora-Care can be used on untreated beams prior to staining, sealing or painting for both active and preventative treatments for wood destroying insects. For curative treatments, apply at a 1:1 ratio, for preventative treatments apply at a 5:1 ratio. Wait for the application to completely dry before painting, staining or sealing which is usually 48 hours. Please viewe the product label for more information. -
Asked by Peter from Caldwell, Nj11/30/2021QIs there a pesticide that can be tank mixed with Bora-Care to treat powder post beetle pupa?
Alternatively is there a pesticide that can be applied pre or post Bora-Care applications to control the emergence of powder post beetle Pupa. Application - interior of barn, spring application.ANo, it is not recommended that Boracare be mixed with any insecticide. We would recommend using Boracare first. Once the product has dried and a sealant has been used, then an insecticide can be used. Please view our Powderpost Beetle Treatment Guide for more information.
-
Asked by Jacob12/15/2021QCan BoraCare be applied after electrical, plumbing and HVAC have been roughed in but before insulation?A
It is recommended to apply Bora-Care before the electrical has been roughed in. The manufacturer has told us that Boracare is not corrosive but of course should not be sprayed onto exposed electrical wiring of any sort. It does state on the product label that it can be used on PVC plumbing pipes.
Read Full Answer »It is recommended to apply Bora-Care before the electrical has been roughed in. The manufacturer has told us that Boracare is not corrosive but of course should not be sprayed onto exposed electrical wiring of any sort. It does state on the product label that it can be used on PVC plumbing pipes. -
Asked by Phil from Green Valley, Az12/16/2021QWhat is the smallest quantity of Boracare I can purchase?A
Bora-Care comes in a concentrated gallon (128 oz) container (case of 4 gallons).
-
Asked by Courtney from Spring12/23/2021QWhy isn't Bora-Care available in smaller quantities?
I only need to treat one small piece of antique wood.A -
Asked by William from Hernando Beach, Fl12/27/2021QHow much BoraCare is needed for stilt home under new construction with 1st level blow out walls measuring 50 x 50, 2 x 4. Nothing on outside yet.A
Each one gallon of Bora-Care will treat 800 square feet of a 2 x 4 stud wall therefore to treat 2500 sq ft (50 ft x 50 ft) you would need a little over 3 gallons of BoraCare. View the full product label and New Construction Bulletin for more information. You can also view our How to Appl…
Read Full Answer »Each one gallon of Bora-Care will treat 800 square feet of a 2 x 4 stud wall therefore to treat 2500 sq ft (50 ft x 50 ft) you would need a little over 3 gallons of BoraCare. View the full product label and New Construction Bulletin for more information. You can also view our How to Apply BoraCare for New Construction Video for a quick demonstration. -
Asked by Daniel from Sapulpa02/14/2022QDo I dilute Bora-Care? If so, how much water is needed because it is thick like honey and I cannot spray it?A
Yes, Boracare MUST be diluted with warm/hot water and should be mixed prior in a large bucket prior to adding to your sprayer (Do NOT mix BoraCare directly in your sprayer) Cool water makes the mixing process difficult and can result in a clogged sprayer. View our How to Mix BoraCare Video here for…
Read Full Answer »Yes, Boracare MUST be diluted with warm/hot water and should be mixed prior in a large bucket prior to adding to your sprayer (Do NOT mix BoraCare directly in your sprayer) Cool water makes the mixing process difficult and can result in a clogged sprayer. View our How to Mix BoraCare Video here for a demonstration. BoraCare is mixed at a 1:1 ratio (Water to BoraCare) for an active infestation and a 5:1 ratio (Water to BoraCare) for preventative. For example, 1 gallon of BoraCare + 1 gallon of water or 5 gallons of water + 1 gallon of BoraCare. View the full product label for more information. -
Asked by Rigo from Edinburg02/20/2022QHow much Dye indicator is needed per gallon of mixed solution for Bora-Care?A
How much indicator dye you need per gallon, depends on the product label of the product you are planning to use with Bora-Care. For example, Turf Mark Blue is used at a rate of 2 to 4 oz (59 mL to 118 mL per 100 gallons of water, 0.02 oz to 0.04 oz (0.59 mL to 1.18 mL) per gallon of water, for t…
Read Full Answer »How much indicator dye you need per gallon, depends on the product label of the product you are planning to use with Bora-Care. For example, Turf Mark Blue is used at a rate of 2 to 4 oz (59 mL to 118 mL per 100 gallons of water, 0.02 oz to 0.04 oz (0.59 mL to 1.18 mL) per gallon of water, for termiticide treatments on wood. View the product label for Turf Mark Blue HERE. -
Asked by Alan from Gordonsville02/23/2022QWill a BoraCare treatment wash out from exterior walls of a log cabin if the application is not sealed after treatment?A
When applied outside it is very important to seal the treatment by using a sealant material, like a Thompsons water seal to lock in the protection, otherwise it can fade due to excess moisture being absorbed into the wood. Bora-Care can only be applied to raw wood and after it is applied to wood o…
Read Full Answer »When applied outside it is very important to seal the treatment by using a sealant material, like a Thompsons water seal to lock in the protection, otherwise it can fade due to excess moisture being absorbed into the wood. Bora-Care can only be applied to raw wood and after it is applied to wood outdoors it must be sealed. However, you could apply it each year if you wanted to, but it is not necessary if you seal it. -
Asked by Conrad from Irvine02/27/2022QCan wood surfaces be glued together after treatment with Bora-Care?
I applied Bora-Care to the wood (pine and cedar) prior to gluing pieces together. On one of the joints that I had to take apart a few minutes after gluing it looked like the glue was not sticking to the surface. This is my first time trying Bora-Care before gluing and wondering if it prevents glue from developing normal adhesion and strength.ABoracare can be applied to any raw wood surface and finished in any way a end user needs. There is no issue with using wood glues on wood that has been treated with Boracare, however you may not have let the wood dry enough before trying to attach them together to allow the glue to form a proper adh…
Read Full Answer »Boracare can be applied to any raw wood surface and finished in any way a end user needs. There is no issue with using wood glues on wood that has been treated with Boracare, however you may not have let the wood dry enough before trying to attach them together to allow the glue to form a proper adhesive to the surface. The Boracare replaces the natural moisture content of the wood with its glycols to protect it through and through. If the wood is too damp still after an application, you may not have the wood accept the glue and stick/dry as quickly as you may expect. -
Asked by Vicki from Hilo, Hi02/28/2022QDoes Bora-Care need to be reapplied since Powder Post Beetle larvae may be at different stages?A
No, Bora-Care should not need to be reapplied if the original application is applied to all accessible wood surfaces (raw wood in bare state), allowed to dry and then sealed with a paint, stain or sealant to lock the Bora-Care application in. Please view our Powderpost Beetle Treatment Guid…
Read Full Answer »No, Bora-Care should not need to be reapplied if the original application is applied to all accessible wood surfaces (raw wood in bare state), allowed to dry and then sealed with a paint, stain or sealant to lock the Bora-Care application in. Please view our Powderpost Beetle Treatment Guide for more information.