DeltaDust containing deltamethrin is the world's first and only 100% waterproof insecticide dust, so it works in the wet and damp places that insects love. Nothing short of running water will disturb Delta Dust, making Delta Dust an ideal crack and crevice treatment. Delta Dust should be applied with a bellows hand duster (sold seperately) which allows you to easily apply the dust in hard to reach areas. One application of Delta Dust will keep on killing insects for up to eight months.

DELTADUST Application Tips:

• DeltaDust is intended for application with a hand or power duster (Actisol DPA or similar equipment), with a paint brush or by other suitable means, for hiding and runaway areas and other places where insects are found.
• In living areas, apply in such a manner as to avoid depositions on exposed surfaces or introducing the material into the air. In the home, all food processing surfaces and utensils should be covered during treatment or thoroughly washed before use. Exposed food should be covered or removed.
• To apply insecticide directly into cracks and crevices, use a bulbous duster or other suitable equipment. Apply lightly and uniformly to infested area. Pay particular attention to: cracks and crevices, service ducts, floors and ceilings, wall voids, around electrical and telephone fittings and equipment, around water and sewer pipes, under and behind cabinets, refrigerators and sinks, around windows and door frames, along baseboards, in attics and crawl spaces. The amount to be applied will vary with the site but should usually be in the range of 2-3 grams of DeltaDust per square yard (or 0.5 lbs per 1000 square feet).

Proper Dusting Tips:

• When applying, the duster should be filled only halfway - no more than two-thirds full. This allows for adequate air space to create the desired air/dust mixture prior to application. If there is too much dust in the duster, clumps of dust on treated surfaces may result, leading to overapplication of the product and messy spills.
• Between each squeeze, the duster should be shaken slightly to get dust floating inside the unit.
• When applying dust into cracks and crevices and on surfaces, gently squeeze the duster to ensure the application of very thin layers of dust. When dusting correctly, you should barely be able to see the dust emerging from the tip of the duster.
• Before relaxing your grip on the duster, pull it away from the surface or crack you are treating to prevent sucking up lint, moisture or debris. Small amounts of these items will eventually cause lumping and/or clogging of the duster.
• Place several pebbles or small ball bearings in your duster to keep the dust agitated and ensure than any clumps are broken up prior to application. Also, always keep the screen inside the duster in place as this is designed to help maintain a fine dust consistency.
• When treating around electrical outlets, use dusters fitted with plastic or fiberglass spouts, or place a small section of rubber hose or plastic tubing over the metal tip to avoid contacting electrical wires. These tubes will also enable you to reach around corners and beneath cabinet voids that would otherwise be impossible to treat.
• Carry a small brush and a damp cloth. These can be used in the event that dust accidentally drifts out of cracks and crevices and onto non-target areas. Use the brush to push excess dust into cracks, and use the cloth to wipe up.
• Do not apply dust to baseboards.
• Apply dust carefully and judiciously so it does not travel to areas where it might represent a hazard. Prevent food contamination by not applying dust to where it could filter down onto food or food areas after it is applied. Also, be aware of any air currents that could transfer dust to containers or other objects, leading to food contamination.
• If the applicator is to apply any kind of dust for extended periods of time, he or she should wear a respirator approved by the National Institute of Occupational Safety and Health (NIOSH).
• When using high-volume or high-pressure equipment to apply dust in attics or sub-floor crawl spaces, wear a NIOSH-approved respirator. Also, shut off fans, air conditioners, and hot-air heating equipment if necessary. If the dust is combustible, put out all flames and pilot lights, and shut down all spark-producing equipment in the treated area to avoid explosions.
• In general, do not place the tip of the duster in a moist location or allow the duster to sit in moist environments as it will absorb water and become clogged. Clogged dusters can be cleaned by scraping out the spout with a piece of stiff wire.
• Always follow the label when using DeltaDust.