GENERAL DISINFECTION

FOR USE AS A GENERAL DISINFECTANT ON HARD, NON-POROUS SURFACES:

1. Pre-clean heavily soiled areas.
2. Apply use solution of 1.5 oz. of this product per 5 gal. of water (or equivalent use dilution) (469 ppm active) to hard, non-porous surfaces using a sponge, brush, cloth, mop, auto scrubber, mechanical spray device, hand pump trigger spray device, coarse trigger spray device. For spray applications, spray 6-8 inches from surface.  DO NOT breathe spray.
3. Treated surfaces must remain wet for 10 minutes.
4. Wipe dry or allow to air dry.
5. Prepare a fresh solution daily or when visibly dirty.

WORK AREAS AND BENCHES, POTS, FLATS AND FLOWER BUCKETS, CUTTING TOOLS:

Pre-clean surfaces. Spray or swab hard, non-porous working surfaces or soak cutting edge of tool with a solution of 1.5 oz. of this product per 5 gal. of water (or equivalent use dilution) before each work period and again after each plant is completed to help control transfer of diseases such as Botrytis, crown rot, downy mildew, Erwinia and root rot†. Allow surface to remain wet for 10 minutes. To apply solution as a sprayer application, use as a coarse spray only and spray 6-8 inches from surface. DO NOT breathe spray. Wipe up excess liquid or allow to air dry. Dry and oil tools at the end of each workday. Prepare a fresh solution daily or when visibly dirty. (†Not for use in CA.)

FLORIST USE DIRECTIONS:

To clean, disinfect and deodorize hard, non-porous surfaces, prepare use solution of 1.5 oz. of this product per 5 gal. of water (or equivalent use dilution). For heavy-duty use, add 3 oz. of this product per 5 gal. of water (or equivalent use dilution). Remove all leaves, petals, garbage and refuse. Pre-clean surfaces using pressurized water where possible. Apply use solution to hard, non-porous surfaces, thoroughly wetting surfaces as required, with a cloth, mop, brush, sponge, auto scrubber, mechanical spray device, hand pump trigger spray device, coarse trigger spray device. For sprayer applications, spray 6-8 inches from surface. DO NOT breathe spray. Rub with brush, sponge, mop or cloth. Treated surfaces must remain wet for 10 minutes. Wipe up excess or allow to air dry. Change cloth, sponge or towels frequently to avoid re-deposition of soil. Prepare a fresh solution daily or when visibly dirty.

ALGAE TREATMENT (Not for use in CA)

GREENHOUSE GLASS (Not for use in CA.):

Spray or swab hard, non-porous surfaces with a solution of 1.5 oz. of this product per 5 gal. of water (or equivalent use dilution). Allow to air dry. Wash off dead algae with water. Spray clean surface again with the solution. DO NOT rinse. For sprayer applications, use as a coarse spray only. Allow surfaces to remain wet for 10 minutes then air dry. Prepare a fresh solution daily or when visibly dirty.

WALKWAYS (Not for use in CA.):

This product will inhibit the growth of algae on hard, non-porous walkways. For heavy infestations, spray or swab surface with a solution of 1.5 oz. of this product per 5 gallons of water (or equivalent use dilution). Let stand for an hour or more then brush and wash away dead algae. Soak area again with the solution. DO NOT rinse. Allow to dry on the surface and repeat application when algae growth returns. For sprayer applications, use as a coarse spray only. Allow surfaces to remain wet for 10 minutes then air dry. Prepare a fresh solution daily or when visibly dirty.

COMMERCIAL FLORIST

DO NOT apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in the area during application. For any requirement specific to your State and Tribe, consult the State/Tribal agency responsible for pesticide regulation.

COMMERCIAL FLORIST USE DIRECTIONS:

To clean, disinfect and deodorize hard, non-porous surfaces, prepare use solution of 1.5 oz. of this product per 5 gal. of water (or equivalent use dilution). For heavy-duty use, add 3 oz. of this product per 5 gal. of water (or equivalent use dilution). Remove all leaves, petals, garbage and refuse. Pre-clean surfaces using pressurized water where possible. Apply use solution to hard, non-porous surfaces, thoroughly wetting surfaces as required, with a cloth, mop, brush, sponge, auto scrubber, mechanical spray device, hand pump trigger spray device, coarse trigger spray device. For sprayer applications, spray 6-8 inches from surface. DO NOT breathe spray. Rub with brush, sponge, mop or cloth. Treated surfaces must remain wet for 10 minutes. Wipe up excess or allow to air dry. Change cloth, sponge or towels frequently to avoid re-deposition of soil. Prepare a fresh solution daily or when visibly dirty.