The Mosquito Control Kit - Ultimate includes products that are easy to measure and apply in quantities that treat larger yards or multiple properties. This kit also offers the versatility of multiple concentrates that can be mixed and applied at the same time. As with all pests, it is crucial to address the environmental conditions that support mosquito populations. While it is unrealistic to expect 100% control of all mosquitoes, taking the time to do a good Inspection so that you can address both land and water conditions that favor mosquitoes will help you get the best results from your mosquito Treatment .

How to Apply the Mosquito Control Kit - Ultimate

STEP 1 - SANITATION

Because mosquitoes need water to lay eggs and develop, finding and eliminating water sources is a crucial step in managing mosquito populations.

*Check for areas where rainwater collects such as bird baths, flowerpots, gutters, rain barrels, pool covers, animal drinking water receptacles, deep hollows in trees, standing puddles, and any other areas where water may collect. Minimize water collection and empty these containers as you are able, and treat other standing water with larvicides (see STEP 2).

*Keep trees and shrubs pruned and grasses short to reduce areas where moisture is retained and adult mosquitoes like to rest.

*Remove or reduce piles of yard debris to reduce harborage areas.

STEP 2 - TREAT STANDING WATER- Altosid Pro-G IGR

Altosid is a ready-to-use granule that contains the insect growth regulator (IGR) Methoprene. Altosid is not a true larvicide, though it does prevent adult mosquito emergence. Granules will gradually sink in water and will release active ingredient continuously for up to 30 days.

*Apply Altosid evenly over the surface of the water to be treated to control mosquitoes before they become breeding, biting adults.

*Use a disposable spoon or other dedicated measuring tool to measure Altosid granules.

*Rates of application are for water less than 2 feet deep, or by total gallons of water for deeper water. Use approximately 80 granules per gallon of water for small applications such as flower pots, urns, old tires, etc. For other applications:

    *1 cup treats 2,400 sq. ft. or 9,600 gallons of water

    *¼ cup treats 600 sq. ft. or 2,400 gallons

    *1 tbsp. treats 150 sq. ft. or 600 gallons

    *½ tbsp. treats 75 sq. ft. or 300 gallons

    *1 tsp. treats 50 sq. ft. or 200 gallons

    *½ tsp. treats 25 sq. ft. or 100 gallons

    *¼ tsp. treats up to 13 sq. ft. or 50 gallons.

*Apply Altosid to temporary and permanent sites which support mosquito larval development such as bird baths, gutters, animal feeding troughs, small ponds, rain barrels, unused swimming pools or hot tubs.

*Altosid also may be used on sites such as salt and tidal marshes, freshwater swamps and marshes, drainage areas, ditches, retention ponds, sewers, catch basins, irrigated croplands, pastures, and orchards. See the product label for complete list of approved sites.

*Application to sites subject to water flow or exchange will diminish effectiveness and may require higher application rates or more frequent applications.

*Altosid is safe for use around fish, aquatic life, amphibians, other beneficial insects, and pets.

*Do not apply to finished human drinking water.

*Store unused granules in a cool, dry place out of reach of children and pets.

STEP 3 - INSECTICIDES and INSECT GROWTH REGULATOR -Talstar P, Archer IGR, ExciteR Insecticide, Maruyama MM181 Mist Blower

There are three concentrates with different active ingredients included in this kit. All of these concentrates must be diluted with water and applied with pressurized spray equipment. We recommend using Talstar P for most applications, adding Archer IGR for heavier populations, and diluting ExciteR with one or both of these solutions to include a faster initial cleanout of existing adult mosquitoes. These concentrates may be applied with the included Maruyama MM91V Mist Blower, or with a pump sprayer.

*Follow the included instructions to assemble the Maruyama MM91V Mist Blower.

*The Maruyama MM91V Mist Blower will hold up to 3 gallons of finished solution.

*We recommend to begin at a low setting, especially if you have not used a mist blower before. The Maruyama MM91V Mist Blower will treat very quickly, and you should aim to apply 1 gallon of finished solution per 1,000 square feet of treatment area. You can dilute insecticides in more water per area if you find you are running out of product too quickly.

*Talstar P contains Bifenthrin, a synthetic pyrethroid that kills adult mosquitoes both upon initial spray and for weeks after application.

*Dilute Talstar P at a rate of 1 oz. of concentrate per gallon of water or per 1,000 square feet of area to be treated.

*To measure Talstar P, squeeze the bottle to fill the small reservoir with the desired amount of concentrate. Remove only the cap on the small reservoir to dispense the pre-measured liquid. *To make dilution, add desired amount of water to spray tank, add Talstar P, then stir, shake, or agitate the tank to ensure proper mixing before spraying.

*Archer IGR contains the active ingredient Pyridine that imitates a growth hormone and prevents full development in immature mosquitoes.

*Dilute Archer IGR at a rate of 1 oz. of concentrate per gallon of water or per 1,000 square feet.

*To measure Archer IGR, squeeze the bottle to fill the small reservoir with the desired amount of concentrate. Remove only the cap on the small reservoir to dispense the pre-measured liquid. Add Archer IGR to dilution after ensuring Talstar P and/or ExciteR is mixed thoroughly.

*ExciteR contains natural pyrethrum, an insecticide that quickly kills insect pests on contact, and Piperonyl Butoxide (PBO), a synergist to stabilize and boost the killing power of insecticides.

*Shake container well before measuring and mixing.

*Dilute ExciteR at a rate of 0.25 - 0.50 oz. of concentrate per 1,000 square feet for most applications. Higher rates may be used for cleanout of very heavy populations: see the product label for complete use rates.

*When mixing ExciteR with Talstar P, match the volume of water with the rate you are using for the Talstar P. For example, if you are using 1 oz. of Talstar P per gallon of water for 1,000 square feet, use 0.25-0.5 oz. of ExciteR per gallon of water. If you are applying Talstar P at a rate of 0.33 oz. in 3 gallons per 1,000 square feet, dilute ExciteR at a rate of 0.08-.17 oz. per gal, or 0.25-0.5 oz. per 3 gallons of water.

*To measure ExciteR, squeeze the bottle to fill the small reservoir with the desired amount of concentrate. Unscrew only the cap on the small reservoir to dispense the pre-measured liquid.

*To make dilution, add at least ½ desired volume of water to spray tank, add ExciteR concentrate, then agitate or close and invert spray tank to mix product. Repeat agitation before spraying to ensure solution is mixed thoroughly.

*When tank mixing multiple products, dilute only what you plant to spray the same day. Do not let tank mixtures sit overnight.

*Apply spray solution to adult mosquito resting areas, including ornamental plants such as dense brush, tall grasses, and especially the undersides of leaves on trees and bushes. Also treat resting areas on structures such as under eaves or other overhangs, under decks and porches, and in other moist, shady areas where mosquitoes may rest or breed.

*Apply when mosquitoes are most active for the best knockdown: spray early in the morning, in the early afternoon, or after sunset.

*Resist the urge to broadcast over the entire yard and home since this may also reduce populations of beneficial insects and predators.

*Do not make applications with this solution that may contaminate water sources such as ponds or streams where there is aquatic life present.

*Do not apply spray solution to edible plants.

*Keep pets and other people out of the treatment area until the application has dried, usually about an hour.

*Mix only the amount of solution you plan to apply within 24 hours. The active ingredient will degrade if left in solution, and the residue may damage your spray equipment.

*Repeat applications every 30-60 days as needed. The solution may be applied more frequently if heavy populations recur, but you must wait at least 7 days between applications.

*Store unused products in the original container in a temperate environment and out of direct sunlight. Store out of reach of children or pets for up to 3 years.